IEC 62209-3: 2019 specifies measurement protocols and test procedures for the reproducible measurement of peak spatial-average specific absorption rate (psSAR) induced inside a simplified model of a human head or body by radio-frequency (RF) transmitting devices, with a specified measurement uncertainty. Requirements are provided for psSAR assessment using vector measurement-based systems. Such systems determine the psSAR by three-dimensional (3D) field reconstruction within the volume of intere...view more

    • sale 10% off
    • Standard
      140 pages
      English language
    • e-Library read for
      1 day

IEC 61290-1-3:2021 is available as IEC 61290-1-3:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61290-1-3:2021 applies to all commercially available optical amplifiers (OA) and optically amplified subsystems. It applies to OA using optically pumped fibres (OFA based on either rare-earth doped fibres or on the Raman effect), semiconductors (SOA), and waveguides (POWA). NOTE 1 The applica...view more

    • sale 10% off
    • Standard
      19 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Amendment
      10 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Amendment
      10 pages
      English language
    • e-Library read for
      1 day

This document specifies the technical delivery conditions for steel pipes (casing, tubing and pup joints), coupling stock, coupling material and accessory material.
By agreement between the purchaser and manufacturer, this document can also be applied to other plain-end pipe sizes and wall thicknesses.
This document is applicable to the following connections:
— short round thread casing (SC);
— long round thread casing (LC);
— buttress thread casing (BC);
— non-upset tubing (NU);
— extern...
view more

    • sale 10% off
    • Standard
      281 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      231 pages
      English language
    • e-Library read for
      1 day

his document is applicable to both self-healing capacitor units and self-healing capacitor banks intended to be used, particularly, for power-factor correction of AC power systems having a rated voltage above 1 000 V and fundamental frequencies of 15 Hz to 60 Hz. The following capacitors are excluded from this document: - shunt power capacitors of the self-healing type for AC systems having a rated voltage up to and including 1 000 V (IEC 60831-1, -2); - shunt power capacitors of the non-self-he...view more

    • sale 10% off
    • Standard
      59 pages
      English language
    • e-Library read for
      1 day

This part of IEC 60068 specifies methods of test applicable to specimens which, during transportation, storage or in service, can be subjected to low air pressure. The object of the low air pressure test is to determine the ability of components, equipment or other articles to be used, transported or stored at low air pressure. Components, equipment or other articles to be used, transported or stored under a simultaneous combination of high or low temperature and low air pressure, where the comb...view more

    • sale 10% off
    • Standard
      13 pages
      English language
    • e-Library read for
      1 day

This Part of EN 10217 specifies the technical delivery conditions in two test categories for welded tubes of circular cross-section made of austenitic and austenitic-ferritic stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures.
NOTE   Once this document is published in the Official Journal of the European Union (OJEU) under Directive 2014/68/EU, pressure equipment directive, presumption of conformity...
view more

    • sale 10% off
    • Standard
      42 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      41 pages
      English language
    • e-Library read for
      1 day

This part of ISO 8437 specifies safety requirements and test procedures applicable to powered ride-on snow
throwers.

    • sale 10% off
    • Standard
      32 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      25 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Standard
      25 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      19 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Standard
      22 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      18 pages
      English language
    • e-Library read for
      1 day

This part of ISO 8437 defines terms and definitions and common test methods applicable to powered walk-behind
and ride-on snow throwers. It is not intended to apply to hand-held snow throwers nor to airport, highway, agricultural or other types of snow removal machines and equipment.
This standard deals with significant hazards, hazardous situations and events relevant to snow throwers used as intended and under the conditions reasonably foreseen by the manufacturer.

    • sale 10% off
    • Standard
      22 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      20 pages
      English language
    • e-Library read for
      1 day

This document describes an extension to ISO 24613-1 and ISO 24613-2 to support the development of detailed descriptions of common etymological phenomena and/or diachronic information with respect to lexical entries in born-digital and/or retro-digitized lexicons. It provides both a meta-model for such an extension as well as the relevant data categories.

    • sale 10% off
    • Standard
      26 pages
      English language
    • e-Library read for
      1 day
    • sale 15% off
    • Standard
      22 pages
      English language
    • sale 15% off
    • Standard
      22 pages
      French language
    • sale 15% off
    • Draft
      22 pages
      English language
    • sale 10% off
    • Draft
      26 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      26 pages
      English language
    • e-Library read for
      1 day
    • sale 15% off
    • Draft
      22 pages
      French language

This document specifies the technical delivery conditions in two test categories for seamless tubes of circular cross section made of austenitic (including creep resisting steel) and austenitic-ferritic stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures.
NOTE   Once this standard is published in the Official Journal of the European Union (OJEU) under Directive 2014/68/EC, presumption of conformity t...
view more

    • sale 10% off
    • Standard
      47 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      45 pages
      English language
    • e-Library read for
      1 day

IEC 63154:2021 specifies requirements, methods of testing and required test results where standards are needed to provide a basic level of protection against cyber incidents (i.e. malicious attempts, which actually or potentially result in adverse consequences to equipment, their networks or the information that they process, store or transmit) for: a) shipborne radio equipment forming part of the global maritime distress and safety system (GMDSS) mentioned in the International Convention for Sa...view more

    • sale 10% off
    • Standard
      65 pages
      English language
    • e-Library read for
      1 day

This International Standard defines terms and specifies safety requirements and test procedures applicable to powered walk-behind snow throwers. It is not intended to apply to hand-held snow throwers nor to airport, highway, agricultural or other types of snow removal machines and equipment.

    • sale 10% off
    • Standard
      25 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      22 pages
      English language
    • e-Library read for
      1 day

2020-05-14: no xml because NNA document

    • sale 10% off
    • Standard
      97 pages
      English language
    • e-Library read for
      1 day

DEN/ERM-TGMAR-611

    • sale 10% off
    • Standard
      21 pages
      English language
    • e-Library read for
      1 day
    • sale 15% off
    • Standard
      21 pages
      English language
    • sale 15% off
    • Standard
      20 pages
      English language
    • sale 15% off
    • Standard
      20 pages
      English language
    • sale 10% off
    • Draft
      20 pages
      English language
    • e-Library read for
      1 day

IEC 60730-2-11:2019 is available as IEC 60730-2-11:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60730-2-11:2019 applies to energy regulators for use in, on, or in association with equipment, including energy regulators for heating, air conditioning and similar applications. The equipment may use electricity, gas, oil, solid fuel, solar thermal energy, etc. or a combination thereof. Th...view more

    • sale 10% off
    • Standard
      17 pages
      English language
    • e-Library read for
      1 day

This document specifies the method intended for assessing the radon diffusion coefficient in waterproofing materials such as bitumen or polymeric membranes, coatings or paints, as well as assumptions and boundary conditions which will be met during the test.
The test method described in this document allows to estimate the radon diffusion coefficient in the range of 10-5 m2/s to 10-12 m2/s[8][9] with an associated uncertainty from 10 % to 40 %.

    • sale 10% off
    • Technical specification
      36 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Technical specification
      33 pages
      English language
    • e-Library read for
      1 day

IEC 62878-1:2019(E) specifies the generic requirements and test methods for device-embedded substrates. The basic test methods for printed board substrate materials and substrates themselves are specified in IEC 61189-3. This part of IEC 62878 is applicable to device-embedded substrates fabricated by use of organic base material, which includes, for example, active or passive devices, discrete components formed in the fabrication process of electronic printed boards, and sheet-formed components....view more

    • sale 10% off
    • Standard
      23 pages
      English language
    • e-Library read for
      1 day

IEC 61810-10:2019, with functional and safety aspects, applies to electromechanical elementary relays (non-specified time all-or-nothing relays) with high capability requirements like breaking or short circuit capabilities and similar for incorporation into low-voltage equipment. These relays may have a specific design to extinguish the electric arc between contacts (e.g. by magnetic blow-out), or use an insulation coordination not covered by IEC 61810-1 (e.g. by gas filled contact chambers), or...view more

    • sale 10% off
    • Standard
      65 pages
      English language
    • e-Library read for
      1 day

IEC 62878-2-5:2019 specifies requirements based on XML schema that represents a design data format for device embedded substrate, which is a board comprising embedded active and passive devices whose electrical connections are made by means of a via, electroplating, conductive paste or printing of conductive material. This data format is to be used for simulation (e.g. stress, thermal, EMC), tooling, manufacturing, assembly, and inspection requirements. Furthermore, the data format is used for t...view more

    • sale 10% off
    • Standard
      55 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Standard
      42 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      39 pages
      English language
    • e-Library read for
      1 day

IEC 61189-5-501:2021 is used to quantify the deleterious effects of flux residues on surface insulation resistance (SIR) in the presence of moisture.

    • sale 10% off
    • Standard
      23 pages
      English language
    • e-Library read for
      1 day

This document specifies the minimum requirements for the qualification of concentrator
photovoltaic (CPV) cells and Cell on Carrier (CoC) assemblies for incorporation into CPV
receivers, modules and systems.
The object of this qualification standard is to determine the optoelectronic, mechanical, thermal,
and processing characteristics of CPV cells and CoCs to show that they are capable of
withstanding assembly processes and CPV application environments. The qualification tests of
this doc...
view more

    • sale 10% off
    • Standard
      37 pages
      English language
    • e-Library read for
      1 day

IEC 62025-2:2019 is available as IEC 62025-2:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62025-2:2019 specifies a test method for the non-electrical characteristics of the surface mounted device (SMD) inductors to be used for electronic and telecommunication equipment. The object of this part of this document is to define methods for measuring mechanical performance only. As the reli...view more

    • sale 10% off
    • Standard
      28 pages
      English language
    • e-Library read for
      1 day

NEW!IEC 60730-2-8:2018 is available as IEC 60730-2-8:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60730-2-8:2018 applies to electrically operated water valves for use in, on or in association with equipment for household and similar use, including heating, air-conditioning and similar applications. The equipment can use electricity, gas, oil, solid fuel, solar thermal energy, etc., or...view more

    • sale 10% off
    • Standard
      51 pages
      English language
    • e-Library read for
      1 day

IEC 61333:2019 specifies marking locations and a coding system of marking on ferrite cores. An alphanumerical marking printed or attached to cores reduces the risk of incorrect assembly, mixing of materials and/or mixing of gapped cores on an assembly line. The markings of the inductance factor AL value or of the gap length are especially important to avoid this kind of problem, and their coding system is specified in this document. This edition includes the following significant technical chang...view more

    • sale 10% off
    • Standard
      11 pages
      English language
    • e-Library read for
      1 day

IEC 61000-6-3:2020 is a generic EMC emission standard applicable only if no relevant dedicated product or product family EMC emission standard has been published. This part of IEC 61000 for emission requirements applies to electrical and electronic equipment intended for use at residential (see 3.1.14) locations. This part of IEC 61000 also applies to electrical and electronic equipment intended for use at other locations that do not fall within the scope of IEC 61000-6-8 or IEC 61000-6-4. The i...view more

    • sale 10% off
    • Standard
      30 pages
      English language
    • e-Library read for
      1 day

2020-01-16 PeC: Annexes ZZ for LVD and EMC are pending on part 1

    • sale 10% off
    • Amendment
      12 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Technical specification
      33 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Technical specification
      30 pages
      English language
    • e-Library read for
      1 day

2021-02-25: TC Off confirmed: can be cited without link to legislation as agreed by BT D162/C064, link removed
2020-05-19: Changed from A1 to new edition further to same change at IEC - Incorporates PR=65448, PR=69668, PR=65339 & PR=65447

    • sale 10% off
    • Standard
      116 pages
      English language
    • e-Library read for
      1 day

This part of IEC 60068 specifies a test method for assessing the corrosion resistance of electrotechnical products components, equipment and materials in a salt mist environment. Its objective is to verify that the comparative quality of a metallic material, with or without corrosion protection, is maintained when exposed to salt mist. This test method is useful for evaluating the quality and the uniformity of coatings applied to protect metals against corrosion. It is particularly useful for de...view more

    • sale 10% off
    • Standard
      20 pages
      English language
    • e-Library read for
      1 day

IEC 61280-2-8:2021 is available as IEC 61280-2-8:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 61280-2-8:2021 specifies two main methods for the determination of low BER values by making accelerated measurements. These include the variable decision threshold method (Clause 5) and the variable optical threshold method (Clause 6). In addition, a third method, the sinusoidal interference...view more

    • sale 10% off
    • Standard
      34 pages
      English language
    • e-Library read for
      1 day

2019-07-17: temporary no candidate for citation because 80/80 + NWIP needed for ‘Performance Criteria’

    • sale 10% off
    • Standard
      36 pages
      English language
    • e-Library read for
      1 day

Amendment of EN 60825-1 in relation to European regulation (LVD2)

    • sale 10% off
    • Amendment
      17 pages
      English language
    • e-Library read for
      1 day

IEC 63093-2:2020 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of pot-cores made of ferrite, and the dimensional limits for coil formers to be used with them, as well as the effective parameter values to be used in calculations involving them. It also gives guidelines on the allowable limits of surface irregularities applicable to pot-cores in accordance with the relevant generic specification. The selection of core sizes and shapes for t...view more

    • sale 10% off
    • Standard
      24 pages
      English language
    • e-Library read for
      1 day

IEC 63093-3:2020 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of half pot-cores made of ferrite, intended to be used in inductive proximity switches. Half pot-cores for inductive proximity switches are also called PS-cores. The selection of core sizes and shapes for this document is based on the philosophy of including those sizes and shapes which are industrial standards, either by inclusion in a national standard, or by broad-based use...view more

    • sale 10% off
    • Standard
      17 pages
      English language
    • e-Library read for
      1 day

The method should be useable for all SRF and will make it possible to obtain a representative sample from a large stock of SRF

    • sale 10% off
    • Standard
      66 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      67 pages
      English language
    • e-Library read for
      1 day

This part of IEC 61760 gives a reference set of requirements, process conditions and related test conditions to be used when compiling specifications of electronic components that are intended for usage in through-hole reflow soldering technology. The object of this document is to ensure that components with leads intended for through-hole reflow and surface mounting components can be subjected to the same placement and mounting processes. Hereto, this document defines test and requirements that...view more

    • sale 10% off
    • Standard
      32 pages
      English language
    • e-Library read for
      1 day

IEC 61300-2-10:2021 is available as IEC 61300-2-10:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61300-2-10:2021 evaluates the effect of loads which is possible to occur when fibre optic devices are exposed to critical situations such as being stepped on, being run over by vehicle tyres, when an evenly-distributed static load is applied to the top surface of a street cabinet or when a ...view more

    • sale 10% off
    • Standard
      14 pages
      English language
    • e-Library read for
      1 day

IEC 60076-22-6:2021 covers the electric fans used in the cooling circuits of power transformers and reactors. It applies to electric fans mounted on liquid immersed power transformers according to IEC 60076-1 and reactors according to IEC 60076-6 with and without conservator for indoor or outdoor installation. It outlines the service conditions and the mechanical and electrical requirements that are common to all the equipment. The electric fans concerned by this document are of the axially oper...view more

    • sale 10% off
    • Standard
      20 pages
      English language
    • e-Library read for
      1 day

IEC 60076-22-5:2021 covers electric pumps used in the cooling circuits of power transformers and reactors. It applies to electric pumps mounted on liquid immersed power transformers according to IEC 60076-1 and reactors according to IEC 60076-6 with and without conservator for indoor or outdoor installation. It outlines the operation requirements for the electrical and hydraulic performance, mechanical design, routine testing and type testing. Additionally, performance and dimensions of preferre...view more

    • sale 10% off
    • Standard
      28 pages
      English language
    • e-Library read for
      1 day