Search Catalog

This document applies to side loaded refuse collection vehicle (RCV), as defined in prEN 1501-1.
This document deals with all significant hazards, hazardous situations and events relevant to the side loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the side loaded RCV so as to ensure that it is fit...view more

This document specifies test methods for the determination of the suitability of two component epoxy and two component polyurethane adhesives for glued-in steel rods in glued laminated timber (GLT) and glued solid timber (GST) according to EN 14080, cross laminated timber (CLT) according to EN 16351 and laminated veneer lumber (LVL) according to EN 14374.
It specifies performance requirements and the determination of characteristic bond strength values for such adhesives for the prefabrication ...view more

This document specifies laboratory test facilities and equipment for sound insulation measurements of building elements, such as: —   components and materials; —   building elements; —   technical elements (small building elements); —   sound insulation improvement systems. It is applicable to laboratory test facilities with suppressed radiation from flanking elements and structural isolation between source and receiving rooms. This document specifies qualification procedures...view more

RES/EE-EEPS37

IEC 61189-5-601:2021 specifies the reflow soldering ability test method for components mounted on organic rigid printed boards, the reflow heat resistance test method for organic rigid printed boards, and the reflow soldering ability test method for the lands of organic rigid printed boards in applications using solder alloys, which are eutectic or near-eutectic tin-lead (Pb), or lead-free alloys. The printed boards materials for this organic rigid printed boards are epoxide woven E-glass lamina...view more

This document specifies terms and definitions related to forage harvesters and their component parts. This document identifies dimensions and other characteristics aimed at allowing comparison of operations of the machines and to improve communication among engineers and researchers, in association with ISOÂ 8909-2, which lays down methods of measuring characteristics and performance requirements for the term defined.

This document specifies requirements for check valves intended for single use and used with infusion equipment for gravity-feed infusion and/or with pressure infusion apparatus.
NOTE   The functional requirements in this document also apply to built-in check valves.

RES/EE-EEPS34

RES/JTC-DRM-35

This document applies to rear loaded refuse collection vehicles (RCV), as defined in 3.2.
This document deals with all significant hazards, hazardous situations and events relevant to the rear loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the rear loaded RCV so as to ensure that it is fit for it...view more

This International Standard provides principles and requirements for safe handling and
storage of solid recovered fuels (SRF).
The International Standard covers the handling, transportation and storage of SRF
throughout the supply chain, from the point of reception of non-hazardous waste.

This European Standard lays down harmonized identifiers for marketed liquid and gaseous fuels. The requirements in this standard are set to complement information needs of users regarding the fuel- and vehicle-compatibility that are placed on the market. The development of this standard focused on vehicles placed on the market for the first time, which does not preclude the application of this standard also to vehicles already in circulation. The identifier is intended to be visualized at dispen...view more

This document deals with all significant hazards, hazardous situations and events relevant to lifting devices used for the emptying of designated refuse containers into RCVs and their fitting onto the RCVs when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer throughout their foreseeable lifetime as defined in Clause 4.
This document is applicable to the design and construction of the refuse container lifting devices and the mounting ...view more

This document describes a method for the sampling and measurement of mercury of both vapour and solid phases on stationary source flue gas streams. Mercury generally exists as elemental (Hg0) and oxidized (Hg2+) forms, both in the vapour and solid phases in flue gases. The vapour-phase (gaseous) mercury is captured either isokinetically or non-isokinetically with a gold amalgamation trap after removing solid-phase (particulate) mercury with a filter. Because gold amalgamation trap captures only ...view more

This document specifies a methodology to define ITS-S communication profiles (ITS-SCPs) based on standardized communication protocols to interconnect trusted devices. These profiles enable secure information exchange between such trusted devices, including secure low-latency information exchange, in different configurations. The present document also normatively specifies some ITS-SCPs based on the methodology, yet without the intent of covering all possible cases, in order to exemplify the meth...view more

2019-11-26: This prCEN ISO/TR 21186-2 is split of prCEN ISO/TR 21186 following the same split at ISO

This document specifies the methods and requirements in assessing the dimensions and performance of a forage harvester, as defined in ISOÂ 8909-1, and its functional components. It also allows comparison of forage harvester performance through comparative testing.

2019-11-26: This prCEN ISO/TR 21186-3 is split of prCEN ISO/TR 21186 following the same split at ISO

This document specifies the basic measurement procedures for airborne and impact sound insulation of building elements in laboratory test facilities.

This document specifies the use of FTIR spectrometry for determining the concentrations of individual volatile organic compounds (VOCs) in waste gases from non-combustion processes. The method can be employed to continuously analyse sample gas which is extracted from ducts and other sources. A bag sampling method can also be applied, if the compounds do not adsorb on the bag material, and is appropriate in cases where it is difficult or impossible to obtain a direct extractive sample.
The princ...view more

DES/EE-0269

This document describes methods for determining air speed and flow direction, CO, NO and NO2 concentrations and visibility in road tunnels using direct-reading instruments. This document specifically excludes requirements relating to instrument conformance testing.

This document specifies terms and definitions that are related to air quality (see 3.1.1.1). These are either general terms or are used in connection with the sampling (see 3.3.3.1) and measurement of gases, vapours (see 3.1.5.8) and airborne particles (see 3.2.2.1) for the determination of air quality.
The terms included are those that have been identified as being fundamental because their definition is necessary to avoid ambiguity and ensure consistency of use.
An alphabetical index of the ...view more

This document specifies test methods for evaluations of forage harvester function and performance, covering forage harvesters which cut the crop directly at full width or from spaced-apart plant rows, or which pick up pre-cut crop. It applies to forage harvesters with driven knives for chopping and which deliver the chopped crop into a container or a separate vehicle or trailer. The forage harvesters can be tractor-mounted, trailed or self-propelled.

This European Standard specifies general requirements for the performance of procedures for the determination of the concentration of chemical agents in workplace atmospheres as required by the Chemical Agents Directive 98/24/EC. The requirements given apply to all measuring procedures, irrespective of the physical form of the chemical agent (gas, vapour, airborne particles), the sampling method and the analytical method used. This European Standard is applicable to all steps of a measuring proc...view more

This document specifies the parameters of integral lighting systems designed to provide illumination in and/or at both stationary and mobile machines to enable the safe use of the machine and the efficient performance of the visual task within and/or at the machine to be carried out by the operator.
This document does not specify lighting systems mounted on the machine to specifically illuminate visual tasks outside the machine. The function and requirements of these systems are specified in th...view more

This document defines the requirements and operation of the on-board vehicle equipment that enables magnetic field wireless power transfer (MF-WPT) for traction battery charging of electric vehicles. It is intended to be used for passenger cars and light duty vehicles.
This document addresses the following aspects for an EV device:
— safety requirements;
— transferred power and power transfer efficiency;
— ground clearance of the EV device;
— functionality with associated off-board systems ...view more

This document establishes the requirements and test methods for rubber and plastics suction hoses for fire-fighting purposes. These hoses can also be used manually to supply unpressurized water to the pump or for water discharge. NOTE      All pressures are expressed in megapascals and in bar (1 MPa = 10 bar). Additional requirements are specified for hose assemblies, that is, hoses with couplings already fitted, where this is carried out by the hose manufacturer (see Clause 8). TypeÂ...view more

This document applies to front loaded refuse collection vehicle (RCV), as defined in 3.2 with closed system defined in 3.13.
This document deals with all significant hazards, hazardous situations and events relevant to the front loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the front loaded RCV ...view more

This document specifies a laboratory test method using test chambers defined in ISO 16000-9 and further specified in EN 16516 and evaluation procedures for the determination of odours emitted from building products and materials.
Sampling, transport and storage of materials under test, as well as preparation of test specimens are described in ISO 16000-11 and further specified in EN 16516.

This European Standard (EN 16157 series) specifies and defines component facets supporting the exchange and shared use of data and information in the field of traffic and travel.
The component facets include the framework and context for exchanges, the modelling approach, data content, data structure and relationships.
This European Standard is applicable to:
-   Traffic and travel information which is of relevance to road networks (non-urban and urban),
-   Public transport information that is ...view more

This document specifies laboratory methods for measuring the impact sound insulation of floor assemblies. The test results can be used to compare the sound insulation properties of building elements, classify elements according to their sound insulation capabilities, help design building products which require certain acoustic properties and estimate the in situ performance in complete buildings. The measurements are performed in laboratory test facilities in which sound transmission via flankin...view more

ISO 4918:2016 specifies methods for determining the change of appearance and stability of a textile floor covering or any damage caused by detachment of layers, opening of joints, or crazing of a resilient or laminate floor covering under the movement of a castor chair.

This document establishes a European grouping system for materials for welding purposes, classified in accordance with the grouping system of ISO/TR 15608. It is also applicable for other purposes such as heat treatment, forming and non-destructive testing. This document covers grouping systems for the following standardized materials: a) steel; b) aluminium and its alloys; c) copper and its alloys; d) cast irons; e) nickel and nickel alloys. For materials that are not assigned to a group in thi...view more

This document specifies a procedure for rating the tendencies of gas turbine fuels to deposit decomposition products within the fuel system. It is applicable to middle distillate and wide-cut fuels and is particularly specified for the performance of aviation gas turbine fuels. The test results are indicative of fuel thermal oxidation stability during gas turbine operation and can be used to assess the level of deposits that form when liquid fuel contacts a heated surface at a specified temperat...view more

This document specifies a laboratory method for measuring the airborne sound insulation of building products, such as walls, floors, doors, windows, shutters, façade elements, façades, glazing, small technical elements, for instance transfer air devices, airing panels (ventilation panels), outdoor air intakes, electrical raceways, transit sealing systems and combinations, for example walls or floors with linings, suspended ceilings or floating floors. The test results can be used to compare th...view more

This document specifies a calculation method for oil-lubricated hydrodynamic plain bearings with complete separation of the thrust collar and tilting pad thrust bearing surfaces by a film of lubricant. This document applies to plain thrust bearings with tilting-type sliding blocks (tilting pads), where a wedge-shaped lubrication clearance gap is automatically formed during operation. The ratio of width to length of one pad can be varied in the range B/LÂ =Â 0,5 to 2. This document is not applica...view more