SIST EN ISO 15874-3:2013/oprA2:2021
(Amendment)Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings - Amendment 2 (ISO 15874-3:2013/DAM 2:2020)
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings - Amendment 2 (ISO 15874-3:2013/DAM 2:2020)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasser-installation - Polypropylen (PP) - Teil 3: Formstücke - Änderung 2 (ISO 15874-3:2013/DAM 2:2020
Not available
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide - Polypropylène (PP) - Partie 3: Raccords - Amendment 2 (ISO 15874-3:2013/DAM 2:2020)
Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo - Polipropilen (PP) - 3. del: Fitingi - Dopolnilo A2 (ISO 15874-3:2013/DAM 2:2020)
General Information
RELATIONS
Standards Content (sample)
SLOVENSKI STANDARD
SIST EN ISO 15874-3:2013/oprA2:2021
01-januar-2021
Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo -
Polipropilen (PP) - 3. del: Fitingi - Dopolnilo A2 (ISO 15874-3:2013/DAM 2:2020)
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3:
Fittings - Amendment 2 (ISO 15874-3:2013/DAM 2:2020)Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasser-installation - Polypropylen
(PP) - Teil 3: Formstücke - Änderung 2 (ISO 15874-3:2013/DAM 2:2020Systèmes de canalisations en plastique pour les installations d'eau chaude et froide -
Polypropylène (PP) - Partie 3: Raccords - Amendment 2 (ISO 15874-3:2013/DAM2:2020)
Ta slovenski standard je istoveten z: EN ISO 15874-3:2013/prA2
ICS:
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST EN ISO 15874-3:2013/oprA2:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------SIST EN ISO 15874-3:2013/oprA2:2021
---------------------- Page: 2 ----------------------
SIST EN ISO 15874-3:2013/oprA2:2021
DRAFT AMENDMENT
ISO 15874-3:2013/DAM 2
ISO/TC 138/SC 2 Secretariat: SNV
Voting begins on: Voting terminates on:
2020-11-26 2021-02-18
Plastics piping systems for hot and cold water
installations — Polypropylene (PP) —
Part 3:
Fittings
AMENDMENT 2
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide — Polypropylène (PP) —
Partie 3: RaccordsAMENDEMENT 2
ICS: 91.140.60; 23.040.45
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 15874-3:2013/DAM 2:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020
---------------------- Page: 3 ----------------------
SIST EN ISO 15874-3:2013/oprA2:2021
ISO 15874-3:2013/DAmd 2
ISO 15874-3:2013/DAM 2:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the World
Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.This document was prepared by the European Committee for Standardization (CEN) Technical
Committee CEN/TC 155, Plastics piping systems and ducting systems, in collaboration with ISO Technical
Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2,
Plastics pipes and fittings for water supplies, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).A list of all parts in the ISO 15875 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
© ISO 2020 – All rights reserved iii
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 4 ----------------------
SIST EN ISO 15874-3:2013/oprA2:2021
ISO 15874-3:2013/DAM 2:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the World
Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.This document was prepared by the European Committee for Standardization (CEN) Technical
Committee CEN/TC 155, Plastics piping systems and ducting systems, in collaboration with ISO Technical
Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2,
Plastics pipes and fittings for water supplies, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).A list of all parts in the ISO 15875 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.© ISO 2020 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST EN ISO 15874-3:2013/oprA2:2021
---------------------- Page: 6 ----------------------
SIST EN ISO 15874-3:2013/oprA2:2021
ISO 15874-3:2013/DAM 2:2020(E)
Plastics piping systems for hot and cold water installations —
Polypropylene (PP) — Part 3: Fittings/ AMENDMENT 2
Page 1, clause 2
Add the normative references
ISO 2768-1 General tolerances — Part 1: Tolerances for linear and angular dimensions without individual
tolerance indicationsISO 2768-2 General tolerances — Part 2: Geometrical tolerances for features without individual tolerance
indicationsISO 6506-1 Metallic materials — Brinell hardness test — Part 1: Test method
ISO 6509-1 Corrosion of metals and alloys — Determination of dezincification resistance of copper alloys
with zinc — Part 1: Test methodISO 6509-2 Corrosion of metals and alloys — Determination of dezincification resistance of copper alloys
with zinc — Part 2: Assessment criteriaISO 6957 Copper alloys — Ammonia test for stress corrosion resistance
Delete the normative reference
EN 1254-3, Copper and copper alloys — Plumbing fittings — Part 3: Fittings with compression ends for use
with plastics pipesPage 2, clause 3.2.1
Replace the existing clause 3.2.1. with the new clause 3.2.1 below.
3.2.1 compression fitting
fitting with internal support in which the joint is made by screwing a union nut along a thread to compress
a ring on the outside wall of the pipe and finally to cause a clamping of the pipe between the ring and the
inner support of the fitting.NOTE 1 to entry The fitting may be with or without sealing element.
Page 2, clause 3.2.2
Replace the existing clause 3.2.2. with the new clause 3.2.2 below.
3.2.2 radial press fitting
fitting, with internal support in which the joint is made by a radial compression of a ring with a pressing
tool on the outside wall of the pipe to cause a clamping of the pipe between the ring and the inner support
of the fitting.NOTE 1 to entry The fitting may be with or without sealing element.
© ISO 2020 – All rights reserved 1
---------------------- Page: 7 ----------------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.