Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings (ISO 15874-3:2013)

This part of ISO 15874 specifies the characteristics of fittings for polypropylene (PP) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems under design pressures and temperatures according to the class of application (see ISO 15874-1:2013, Table 1). It covers a range of service conditions (application classes) and design pressure classes. For values of TD, Tmax and Tmal in excess of those in Table 1 of ISO 15874-1:2013 do not apply. NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. It also specifies the parameters for the test methods referred to in this part of ISO 15874. In conjunction with the other parts of ISO 15874, this part of ISO 15874 is applicable to fittings made from PP and to fittings made from other materials which are intended to be fitted to pipes conforming to ISO 15874-2 for hot and cold water installations, whereby the joints conform to the requirements of ISO 15874-5. This part of ISO 15874 is applicable to fittings of the following types:
— socket fusion fittings;
— electro fusion fittings;
— mechanical fittings;
— fittings with incorporated inserts.
It is also applicable to fittings made from alternative materials which when fitted to pipes conforming to ISO 15874-2, conform to the requirements of ISO 15874-5.

Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polypropylen (PP) - Teil 3: Formstücke (ISO 15874-3:2013)

Dieser Teil der ISO 15874 legt Anforderungen an Formstücke für Rohrleitungssysteme aus Polypropylen (PP) fest, die in der Warm- und Kaltwasserinstallation innerhalb von Gebäuden für den Transport von Trink- oder Brauchwasser (Hausinstallation) sowie für Heizungsanlagen unter Berücksichtigung des betreffenden zulässigen Betriebsdruckes und der für die jeweilige Anwendungsklasse geltenden Temperaturen (siehe ISO 15874-1, Tabelle 1) eingesetzt werden.
Diese Norm enthält Festlegungen zu Anwendungsklassen, die sich auf Betriebsbedingungen beziehen, sowie Festlegungen über zulässige Betriebsdrücke. Diese Norm gilt nicht, wenn für TD, Tmax und Tmal höhere als die in Tabelle 1 von Teil 1 dieser Norm aufgeführten Werte zugrunde gelegt werden.
ANMERKUNG   Der Anwender bzw. Auftraggeber ist unter Berücksichtigung der eigenen Anforderungen sowie der geltenden nationalen Festlegungen und Verlegepraktiken für die entsprechende Auswahl dieser Kriterien verantwortlich.
Sie legt auch die Prüfparameter für die Prüfverfahren fest, auf die in dieser Norm verwiesen wird.
Zusammen mit den übrigen Teilen der ISO 15874 (siehe Vorwort) gilt dieser Teil für Formstücke aus PP, anderen Kunststoffen oder metallenen Werkstoffen, die für die Verwendung mit Rohren nach ISO 15874 2 in der Warm- und Kaltwasserinstallation vorgesehen sind und deren Verbindungen den Anforderungen der ISO 15874-5 entsprechen.
Diese Norm ist auch auf Formstücke aus alternativen Werkstoffen anwendbar, die in Verbindung mit Rohren nach Teil 2 die Anforderungen nach ISO 15874-5 erfüllen.
Diese Norm gilt für die folgenden Arten von Formstücken:
-   Formstücke für Muffenschweißung
-   Formstücke für Heizwendelschweißung
-   mechanische Rohrverbinder
-   Formstücke mit integrierten Einsätzen

Systèmes de canalisations en plastique pour les installations d'eau chaude et froide - Polypropylène (PP) - Partie 3: Raccords (ISO 15874-3:2013)

L'ISO 15874-3:2013 spécifie les caractéristiques des raccords pour les systèmes de canalisations en polypropylène (PP) destinés aux installations d'eau chaude et froide à l'intérieur des bâtiments pour le transport de l'eau, que celle-ci soit destinée ou non à la consommation humaine (systèmes domestiques), ainsi qu'aux installations de chauffage à des pressions et des températures de service correspondant à la classe d'application.
L'ISO 15874-3:2013 couvre une gamme de conditions de service (classes d'application) et de classes de pression de service.
Elle spécifie aussi les paramètres d'essai pour les méthodes.
Conjointement avec les autres parties de l'ISO 15874, l'ISO 15874-3:2013 s'applique aux raccords en polypropylène (PP) et aux raccords fabriqués dans d'autres matières qui sont destinés à être assemblés à des tubes conformes à l'ISO 15874‑2 pour les installations d'eau chaude et froide et où les assemblages sont conformes aux exigences de l'ISO 15874‑5.
L'ISO 15874-3:2013 s'applique aux raccords répondant aux types suivants:
raccords à emboîture soudable;
raccords électrosoudables;
raccords mécaniques;
raccords avec inserts incorporés.

Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo - Polipropilen (PP) - 3. del: Fitingi (ISO 15874-3:2013)

Ta del standarda ISO 15874 določa značilnosti fitingov za cevne sisteme iz polipropilena (PP), ki se uporabljajo za napeljave z vročo in hladno vodo za prenos pitne in nepitne vode v stavbah (gospodinjski sistemi), ter za sisteme ogrevanja glede na predvidene tlake in temperature v skladu z razredom uporabe (glej standard ISO 15874-1:2013, preglednica 1). Zajema različne pogoje uporabe (razrede uporabe) in razrede predvidenih tlakov. Ne uporablja se za vrednosti TD, Tmaks in Tmal, ki presegajo vrednosti iz preglednice 1 standarda ISO 15874-1:2013. OPOMBA: Za ustrezno izbiro teh vidikov je odgovoren kupec ali projektant, pri čemer mora upoštevati posebne zahteve ter vse pomembne nacionalne predpise in prakse ali kodekse vgradnje. Določa tudi parametre za preskusne metode iz tega dela standarda ISO 15874. Ta del standarda ISO 15874 se v povezavi z drugimi deli standarda ISO 15874 uporablja za fitinge iz polipropilena in fitinge iz drugih materialov, ki so namenjeni za pritrditev na cevi za napeljave z vročo in hladno vodo v skladu s standardom ISO 15874-2, pri čemer spoji izpolnjujejo zahteve standarda ISO 15874-5. Ta del standarda ISO 15874 se uporablja za fitinge teh vrst:
– varilni fitingi z vtiči;
– elektrofuzijski fitingi;
– mehanični fitingi;
– fitingi z vstavki.
Uporablja se tudi za fitinge iz drugih materialov, ki nameščeni na cevi v skladu s standardom ISO 15874-2 izpolnjujejo zahteve standarda ISO 15874-5.

General Information

Status
Published
Public Enquiry End Date
29-Nov-2010
Publication Date
13-Mar-2013
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
28-Feb-2013
Due Date
05-May-2013
Completion Date
14-Mar-2013

Relations

Buy Standard

Standard
EN ISO 15874-3:2013
English language
23 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 15874-3:2013
01-april-2013
1DGRPHãþD
SIST EN ISO 15874-3:2004
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DQDSHOMDYH]YURþRLQKODGQRYRGR
3ROLSURSLOHQ 33 GHO)LWLQJL ,62
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3:
Fittings (ISO 15874-3:2013)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polypropylen
(PP) - Teil 3: Formstücke (ISO 15874-3:2013)
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide -
Polypropylène (PP) - Partie 3: Raccords (ISO 15874-3:2013)
Ta slovenski standard je istoveten z: EN ISO 15874-3:2013
ICS:
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST EN ISO 15874-3:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 15874-3:2013

---------------------- Page: 2 ----------------------

SIST EN ISO 15874-3:2013


EUROPEAN STANDARD
EN ISO 15874-3

NORME EUROPÉENNE

EUROPÄISCHE NORM
February 2013
ICS 23.040.45; 91.140.60 Supersedes EN ISO 15874-3:2003
English Version
Plastics piping systems for hot and cold water installations -
Polypropylene (PP) - Part 3: Fittings (ISO 15874-3:2013)
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für die Warm- und
installations d'eau chaude et froide - Polypropylène (PP) - Kaltwasserinstallation - Polypropylen (PP) - Teil 3:
Partie 3: Raccords (ISO 15874-3:2013) Formstücke (ISO 15874-3:2013)
This European Standard was approved by CEN on 5 January 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15874-3:2013: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 15874-3:2013
EN ISO 15874-3:2013 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 15874-3:2013
EN ISO 15874-3:2013 (E)
Foreword
This document (EN ISO 15874-1:2013) has been prepared by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN, in collaboration with Technical
Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2013, and conflicting national standards shall be withdrawn at
the latest by August 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15874-3:2003.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 15874-3:2013

---------------------- Page: 6 ----------------------

SIST EN ISO 15874-3:2013
INTERNATIONAL ISO
STANDARD 15874-3
Second edition
2013-02-15
Plastics piping systems for hot and cold
water installations — Polypropylene (PP) —
Part 3:
Fittings
Systèmes de canalisations en plastique pour les installations d’eau
chaude et froide — Polypropylène (PP) —
Partie 3: Raccords
Reference number
ISO 15874-3:2013(E)
©
ISO 2013

---------------------- Page: 7 ----------------------

SIST EN ISO 15874-3:2013
ISO 15874-3:2013(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 15874-3:2013
ISO 15874-3:2013(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions, symbols and abbreviated terms . 2
3.2 Mechanical fittings . 2
3.3 Fittings for fusion . 3
4 Material characteristics . 3
4.1 Plastics fitting material . 3
4.2 Metallic fitting material . 5
4.3 Influence on water intended for human consumption . 5
5 General characteristics . 5
5.1 Appearance . 5
5.2 Opacity . 5
6 Geometrical characteristics . 6
6.1 General . 6
6.2 Dimensions of sockets for socket fusion and electrofusion fittings . 6
6.3 Dimensions of metallic fittings . 9
7 Mechanical characteristics of plastics fittings .10
7.1 General .10
7.2 Fitting material identical to the PP pipe compound .10
7.3 Fitting made from PP not identical to the PP pipe compound .10
7.4 Fittings made from plastics other than PP .10
8 Physical and chemical characteristics of plastics components .12
9 Sealing elements .13
10 Performance requirements .13
11 Marking .13
11.1 General requirements .13
11.2 Minimum required marking .13
11.3 Additional marking .14
Bibliography .15
© ISO 2013 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 15874-3:2013
ISO 15874-3:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
ISO 15874-3 was prepared by Technical Committee CEN/TC 155, Plastics piping systems and ducting systems,
in collaboration with Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of
fluids, and Subcommittee SC 2, Plastics pipes and fittings for water supplies, in accordance with the Agreement
on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 15874-3:2003 and ISO 15874-3:2003/Amd
1:2007), which has been technically revised.
The following material has been revised:
— in 4.1.1, Table 1, the material PP-RCT has been included;
— in 6.2.1, Figure 1 has been simplified, and in Tables 3 and 4, the socket length and socket dimensions
of socket fusion fittings have been adjusted;
— in 6.2.2, Table 5, the socket dimensions for electrofusion fittings have been extended to 160 mm; and
— in 7.4, Tables 6, 7 and 8, values have been adjusted.
1)
ISO 15874 consists of the following parts under the general title Plastics piping systems for hot and cold water
installations — Polypropylene (PP):
— Part 1: General
— Part 2: Pipes
— Part 3: Fittings
— Part 5: Fitness for purpose of the system
— Part 7: Guidance for the assessment of conformity [Technical specification]
1) For ancillary equipment separate standards can apply. Guidance on installation of plastics piping systems made from
different materials intended to be used for hot and cold water installations is given by CEN/TR 12108 [1].
iv © ISO 2013 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 15874-3:2013
ISO 15874-3:2013(E)
Introduction
This part of ISO 15874 specifies the requirements for a piping system and its components when made from
polypropylene (PP). The piping system is intended to be used for hot and cold water installations.
Regarding potential undesirable effects on the quality of water intended for human consumption, caused by
the product covered by ISO 15874
— no information is provided as to whether the product can be used without restriction, and
— existing national regulations concerning the use and/or the characteristics of this product remain in force.
Requirements and test methods for materials and components, other than fittings, are specified in ISO 15874-1
and ISO 15874-2. Characteristics for fitness for purpose (mainly for joints) are covered in ISO 15874-5.
ISO/TS 15874-7 gives guidance for the assessment of conformity.
This part of ISO 15874 specifies the characteristics of the fittings.
At the date of publication of this part of ISO 15874, the following system International Standards for piping
systems of other plastics materials used for the same application are
— ISO 15875, Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X)
— ISO 15876, Plastics piping systems for hot and cold water installations — Polybutylene (PB)
— ISO 15877, Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl
chloride) (PVC-C)
— ISO 22391, Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature
resistance (PE-RT)
The International Organization for Standardization (ISO) draws attention to the fact that it is claimed that
compliance with this document may involve the use of a patent.
ISO takes no position concerning the evidence, validity and scope of this patent right.
The holder of this patent right has assured ISO that they are willing to negotiate licences under reasonable and
non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of
the holder of this patent right is registered with ISO. Information may be obtained from:
Borealis AG
Wagramerstrasse 17-19, A-1220,
Vienna, Austria
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights
other than those identified above. ISO shall not be held responsible for identifying any or all such patent rights.
ISO (www.iso.org/patents) and IEC (http://patents.iec.ch) maintain on-line databases of patents relevant to their
standards. Users are encouraged to consult the databases for the most up to date information concerning patents.
© ISO 2013 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 15874-3:2013

---------------------- Page: 12 ----------------------

SIST EN ISO 15874-3:2013
INTERNATIONAL STANDARD ISO 15874-3:2013(E)
Plastics piping systems for hot and cold water installations —
Polypropylene (PP) —
Part 3:
Fittings
1 Scope
This part of ISO 15874 specifies the characteristics of fittings for polypropylene (PP) piping systems intended
to be used for hot and cold water installations within buildings for the conveyance of water, whether or not
intended for human consumption (domestic systems) and for heating systems under design pressures and
temperatures according to the class of application (see ISO 15874-1:2013, Table 1).
It covers a range of service conditions (application classes) and design pressure classes. For values of T ,
D
T and T in excess of those in Table 1 of ISO 15874-1:2013 do not apply.
max mal
NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects,
taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It also specifies the parameters for the test methods referred to in this part of ISO 15874.
In conjunction with the other parts of ISO 15874, this part of ISO 15874 is applicable to fittings made from PP
and to fittings made from other materials which are intended to be fitted to pipes conforming to ISO 15874-2 for
hot and cold water installations, whereby the joints conform to the requirements of ISO 15874-5.
This part of ISO 15874 is applicable to fittings of the following types:
— socket fusion fittings;
— electro fusion fittings;
— mechanical fittings;
— fittings with incorporated inserts.
It is also applicable to fittings made from alternative materials which when fitted to pipes conforming to
ISO 15874-2, conform to the requirements of ISO 15874-5.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable
for its application. For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions,
tolerances and designation
ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions
ISO 1133-1, Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR)
of thermoplastics.
ISO 1167-1 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the
resistance to internal pressure — Part 1: General method
© ISO 2013 – All rights reserved 1

---------------------- Page: 13 ----------------------

SIST EN ISO 15874-3:2013
ISO 15874-3:2013(E)
ISO 1167-3 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the
resistance to internal pressure — Part 3: Preparation of components
ISO 1167-4 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the
resistance to internal pressure — Part 4: Preparation of assemblies
ISO 7686, Plastics pipes and fittings — Determination of opacity
ISO 9080, Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of
thermoplastics materials in pipe form by extrapolation
ISO 15874-1:2013, Plastics piping systems for hot and cold water installations — Polypropylene (PP) —
Part 1: General
ISO 15874-2:2013, Plastics piping system for hot and cold water installations — Polypropylene (PP) — Part 2: Pipes
ISO 15874-5, Plastics piping system for hot and cold water installations — Polypropylene (PP) — Part 5:
Fitness for purpose of the system
EN 681-1, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 1: Vulcanized rubber.
EN 681-2, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 2: Thermoplastic elastomers.
EN 1254-3, Copper and copper alloys — Plumbing fittings — Part 3: Fittings with compression ends for use
with plastics pipes.
EN 10088-1, Stainless steels — Part 1: List of stainless steels.
EN 10226-1, Pipe threads where pressure-tight joints are made on the threads — Part 1: Taper external
threads and parallel internal treads — Dimensions, tolerances and designation.
3 Terms and definitions, symbols and abbreviated terms
For the purposes of this document, the terms and definitions, symbols and abbreviations given in ISO 15874-1
and the following apply
3.1
fitting
component of a piping system, which connects two or more pipes and/or fittings together, without any further function
3.2 Mechanical fittings
3.2.1
compression fitting
fitting in which the joint is made by the compression of a ring or sleeve on the outside wall of the pipe with or
without additional sealing elements and with internal support
3.2.2
crimped fitting
fitting in which the joint is made by crimping of the fitting and/or a ring on the outside wall of the pipe by means
of a special tool
3.2.3
flanged fitting
fitting in which the pipe connection consists of two mating flanges which are mechanically pressed together
and sealed by the compression of an elastomeric sealing element between them
2 © ISO 2013 – All rights reserved

---------------------- Page: 14 ----------------------

SIST EN ISO 15874-3:2013
ISO 15874-3:2013(E)
3.2.4
flat seat union fitting
fitting in which the pipe connection consists primarily of two components, at least one of which normally
incorporates a flat sealing surface, which are mechanically pressed together by means of screwed nut or
similar and sealed by the compression of an elastomeric sealing element between them
3.3 Fittings for fusion
3.3.1
socket fusion fitting
fitting in which the joint with the pipe is made by melting together the outer part of the pipe with the inner part of
the fitting by means of heat induced by heated tool
3.3.2
electro fusion fitting
fitting in which the joint with the pipe is made by melting together the outer part of the pipe and the inner part of
the fitting by means of heat induced by current flowing in an appropriate resistor inserted in the fitting body
3.4
fitting with incorporated inserts
fitting in which the joint is made by means of connecting threads or other outlets, inserted in the plastics body
combined with fusion ends for socket fusion or electro fusion
4 Material characteristics
4.1 Plastics fitting material
4.1.1 Fitting material identical to the PP pipe compound
The PP compound shall comply with ISO 15874-1:2013, 5.1.
The material shall be tested in form of tubular test pieces.
When tested in accordance with the test methods specified in Table 1, using the indicated parameters, the test
pieces shall withstand the hydrostatic test pressure, p , given in Table 6, 7, 8 or 9 without bursting or leakage.
F
© ISO 2013 – All rights reserved 3

---------------------- Page: 15 ----------------------

SIST EN ISO 15874-3:2013
ISO 15874-3:2013(E)
Table 1 — Mechanical characteristic of tubular test pieces made of PP by injection moulding
Characteristic Requirement Test parameters for the individual tests Test method
Resistance to No bursting or PP-H ISO 1167-1 and
internal pressure leakage during ISO 1167-3
Hydrostatic Test Test period Number of
the test period
(hoop) stress temp. test pieces
MPa °C h
21,0 20 1 3
3,6 95 1000 3
PP-B
Hydrostatic Test Test period Number of
(hoop) stress temp. test pieces
MPa °C h
16,0 20 1 3
2,6 95 1000 3
PP-R
Hydrostatic Test Test period Number of
(hoop) stress temp. test pieces
MPa °C h
16,0 20 1 3
3,5 95 1000 3
PP-RCT
Hydrostatic Test Test period Number of
(hoop) stress temp. test pieces
MPa °C h
15,0 20 1 3
3,8 95 1000 3
Test parameters for all tests
a
Sampling procedure
Type of end cap Type A
Orientation of test piece Not specified
Type of test Water-in–water
a [2]
The sampling procedure is not specified. For guidance see ISO/TS 15874-7 .
4.1.2 PP Fitting material not identical to the PP pipe compound
4.1.2.1 Evaluation of σ -values and control points
LPL
The fitting material in form of injection-moulded or extruded tubular test pieces shall be evaluated by using the
method given in ISO 9080 or equivalent where internal pressure tests are made in accordance with ISO 1167-1
and ISO 1167-3 to find the σ -values. The σ -values thus determined shall be used to determine the design
LPL LPL
stress, σ , (see Annex A of ISO 15874-2:2013) and values of hydrostatic stress, σ , corresponding to the
DF F
temperature and time control points given in Table 2.
NOTE One equivalent way of evaluation is to calculate the σ -value for each temperature (for example 20 °C, 60 °C
LPL
and 95 °C) individually.
If evaluation using the method given in ISO 9080 or equivalent is available from long-term internal pressure
tests relative to extruded pipes of the same compound as used for the fitting, the relevant test temperature shall
be equal to or higher than the maximum design temperature, T , for the service condition class.
max
4 © ISO 2013 – All rights reserved

---------------------- Page: 16 ----------------------

SIST EN ISO 15874-3:2013
ISO 15874-3:2013(E)
Table 2 — Control points for testing fitting materials with tubular test pieces relative to classification
of service conditions
All application Application
classes
Class 1 Class 2 Class 4 Class 5
Maximum design temperature, T , in °C — 80 80 70 90
max
a a
Test temperature, T , in °C 20 95 95 80 95
Test
Test duration, in h 1 1000 1000 1000 1000
a
Conducted at 95 °C to match existing test facilities.
It is recommended that the nominal diameter of the injection-moulded tubular test pieces should be in the
range of the nominal diameters of fittings normally produced by the manufacturer.
4.1.2.2 Thermal stability
When testing the thermal stability by hydrostatic pressure testing in accordance with ISO 1167-1 at 110 °C for
8 760 h, using a test piece in pipe form or a fitting connected to pipes, the test piece shall withstand the test
without bursting. The test shall be conducted in water-in-air at an internal pressure equivalent to the hydrostatic
stress used in the pipe material thermal stability test.
If a fitting connected to pipes is used as a test piece and the pipe connection fails then the thermal stability test
shall be repeated using a test piece in pipe form.
4.1.3 Plastics fitting material other than PP
Plastics material, other than PP, for fittings intended to be used in PP piping systems for hot and cold water
within buildings for the conveyance of water, whether or not for human consumption (domestic systems) and
for heating systems shall conform to 4.1.2.
4.2 Metallic fitting material
Metallic material for fittings intended to be used with components conforming to ISO 15874 shall conform to the
requirements given in EN 1254-3 or EN 10088-1, as applicable.
4.3 Influence on water intended for human consumption
The material shall conform to ISO 15874-1.
5 General characteristics
5.1 Appearance
When viewed without magnification, the internal and external surfaces of fittings shall be smooth, clean and
free from scoring, cavities, and other surface defects to an extent that would prevent conformity to this standard.
The material shall not contain visible impurities. Slight variations in appearance of the colour shall be permitted.
Each end of a fitting shall be square to its axis.
5.2 Opacity
Fittings that are declared to be opaque shall not transmit more than 0,2 % of visible light when tested in
accordance with ISO 7686.
NOTE This test is not necessary when the fitting body is made from a compound already declared opaque for the
production of pipes.
© ISO 2013 – All rights reserved 5

---------------------- Page: 17 ----------------------

SIST EN ISO 15874-3:2013
ISO 15874-3:2013(E)
6 Geometrical characteristics
6.1 General
Dimensions shall be measured in accordance with ISO 3126.
6.1.1 Nominal diameter(s)
The nominal diameter(s), d , of a fitting shall correspond to and be designated by the nominal outside diameter(s)
n
of the pipe(s) conforming to ISO 15874-2 for which they are designed.
6.1.2 Angles
The preferred nominal angles of non-straight fittings are 45° and 90°.
6.1.3 Threads
Threads used for jointing shall conform to EN 10226-1. Where a thread is used as a fastening thread for jointing
an assembly (e.g. union nuts) it shall conform to ISO 228-1 except that these requirements need not apply to
the threads used by the manufacturer to join component parts of a fitting together.
6.2 Dimensions of sockets for socket fusion and electrofusion fittings
6.2.1 Dimensions of socket fusion fitting
Socket fusion fittings shall be classified in two types as follows:
Type A Fittings intended to be used with pipes, where no external machining of the pipe is required
Type B Fittings intended to be used with pipes, where machining of the outside surface of the pipe is necessary
in accordance with the instructions of the manufacturer
The nominal diameter
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.