ISO 14535:2001

INTERNATIONAL ISO
STANDARD 14535
First edition
2001-07-15
Photography — Room-light loading
packages for electronic scanners and
image-setting film and paper rolls —
Dimensions and related requirements
Photographie — Emballages de chargement à la lumière artificielle pour
scanners électroniques, et films et rouleaux de papier pour régler l'image —
Dimensions et exigences connexes
Reference number
ISO 14535:2001(E)
© ISO 2001

---------------------- Page: 1 ----------------------
ISO 14535:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be
edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, elec-
tronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's mem-
ber body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
©
ii ISO 2001 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 14535:2001(E)
Contents Page
1 Scope . 1
2 Normative references . 1
3 Conditions for measurement of dimensions . 1
4 Film and paper dimensions . 1
5 Winding orientation . 1
6 Dimensions of flanges . 2
7 Packaging . 4
8 Leader . 4
9 Package marking . 5
10 Compliance . 5
Bibliography. 6
©
ISO 2001 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 14535:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 14535 was prepared by Technical Committee ISO/TC 42, Photography.
©
iv ISO 2001 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 14535:2001(E)
Introduction
Room-light operation has become increasingly attractive to users of electronic-scanner output equipment and image-
setting devices. This equipment requires accurate cassettes and a good sensitized material/equipment interface,
especially where accurate registration is an important feature, e.g. in colour work.
This International Standard is required in order to define the room-light loading packages which must interface with
the above equipment.
©
ISO 2001 – All rights reserved v

---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 14535:2001(E)
Photography — Room-light loading packages for electronic
scanners and image-setting film and paper rolls — Dimensions and
related requirements
1 Scope
This International Standard applies to room-light loading packages either containing photographic film or paper rolls
for electronic scanners or image-setting devices. It specifies the dimensions of the package and its contents, critical
equipment interfacing features, and package marking. The prime aim of this International Standard is to ensure
compatibility between room-light loading packages and the equipment in which it is used.
Two types of package are recognized. One type uses a rigid flange into which mandrils on the exposing device are
inserted. The other type uses a flexible flange and relies on the exposing equipment design to hold the roll correctly
in the machine.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 554:1976, Standard atmospheres for conditioning and/or testing — Specifications.
ISO 3772:2000, Photogr
...