EN ISO 13259:2018
(Main)Thermoplastics piping systems for underground non-pressure applications - Test method for leaktightness of elastomeric sealing ring type joints (ISO 13259:2018)
Thermoplastics piping systems for underground non-pressure applications - Test method for leaktightness of elastomeric sealing ring type joints (ISO 13259:2018)
This document specifies a test method for determining the leak tightness of elastomeric sealing ring type joints for buried thermoplastics non-pressure piping systems.
Unless otherwise specified in the referring standard, the tests are carried out at the following basic test pressures:
— p1: internal negative air pressure (partial vacuum);
— p2: a low internal hydrostatic pressure;
— p3: a higher internal hydrostatic pressure.
It also describes the following four test conditions under which the tests are performed:
a) Condition A: without any additional diametric or angular deflection;
b) Condition B: with diametric deflection;
c) Condition C: with angular deflection;
d) Condition D: with simultaneous angular and diametric deflection.
The applicable selection of the test pressure(s) and the test condition(s) is specified in the referring standard
Erdverlegte Rohrleitungssysteme aus Thermoplasten für drucklose Anwendungen - Prüfverfahren für die Dichtheit von elastomeren Dichtringverbindungen (ISO 13259:2018)
Dieses Dokument legt ein Prüfverfahren für die Bestimmung der Dichtheit elastomerer Dichtringverbindungen
für erdverlegte drucklose Rohrleitungssysteme aus Thermoplasten fest.
Sofern in der bezugnehmenden Norm nicht anders festgelegt, werden die Prüfungen bei den folgenden
grundlegenden Prüfdruckarten durchgeführt:
— p1: negativer Luftdruck innen (partielles Vakuum);
— p2: niedriger hydrostatischer Innendruck;
— p3: höherer hydrostatischer Innendruck.
Es beschreibt außerdem vier Prüfbedingungen, unter denen die Prüfung ausgeführt wird:
a) Bedingung A: ohne zusätzliche Rohrverformung oder Abwinkelung;
b) Bedingung B: mit Rohrverformung;
c) Bedingung C: mit Abwinkelung;
d) Bedingung D: mit gleichzeitiger Rohrverformung und Abwinkelung.
Die passende Auswahl des/der Prüfdrucks/-drücke und der Prüfbedingung(en) ist in der bezugnehmenden
Norm festgelegt.
Systèmes de canalisations en thermoplastiques pour applications enterrées sans pression - Méthodes d'essai d'étanchéité des assemblages à bague d'étanchéité en élastomère (ISO 13259:2018)
L'ISO 13259:2010 spécifie trois pressions d'essai fondamentales pour déterminer l'étanchéité de l'assemblage à bague d'étanchéité en élastomère, pour les systèmes de canalisations thermoplastiques enterrés sans pression. Elle décrit également quatre conditions d'essai dans lesquelles l'essai peut être réalisé.
Plastomerni cevni sistemi, položeni v zemljo, ki delujejo po težnostnem principu - Metoda za preskus tesnjenja spojev z elastomernimi tesnilnimi obroči (ISO 13259:2018)
Standard ISO 13259:2010 določa tri osnovne preskusne tlake za določanje tesnjenja spojev z elastomernimi tesnilnimi obroči za plastomerne cevne sisteme, položene v zemljo. Prav tako opisuje štiri pogoje za izvajanje preskusa.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 13259:2018
01-september-2018
1DGRPHãþD
SIST EN 1277:2004
3ODVWRPHUQLFHYQLVLVWHPLSRORåHQLY]HPOMRNLGHOXMHMRSRWHåQRVWQHPSULQFLSX
0HWRGD]DSUHVNXVWHVQMHQMDVSRMHY]HODVWRPHUQLPLWHVQLOQLPLREURþL ,62
Thermoplastics piping systems for underground non-pressure applications - Test method
for leaktightness of elastomeric sealing ring type joints (ISO 13259:2018)
Erdverlegte Rohrleitungssysteme aus Thermoplasten für drucklose Anwendungen -
Prüfverfahren für die Dichtheit von elastomeren Dichtringverbindungen (ISO
13259:2018)
Systèmes de canalisations en thermoplastiques pour applications enterrées sans
pression - Méthodes d'essai d'étanchéité des assemblages à bague d'étanchéité en
élastomère (ISO 13259:2018)
Ta slovenski standard je istoveten z: EN ISO 13259:2018
ICS:
23.040.80 Tesnila za cevne zveze Seals for pipe and hose
assemblies
91.140.80 Drenažni sistemi Drainage systems
SIST EN ISO 13259:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 13259:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 13259:2018
EN ISO 13259
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2018
EUROPÄISCHE NORM
ICS 23.040.20; 91.140.80 Supersedes EN 1277:2003
English Version
Thermoplastics piping systems for underground non-
pressure applications - Test method for leaktightness of
elastomeric sealing ring type joints (ISO 13259:2018)
Systèmes de canalisations en thermoplastiques pour Erdverlegte Rohrleitungssysteme aus Thermoplasten
applications enterrées sans pression - Méthodes für drucklose Anwendungen - Prüfverfahren für die
d'essai d'étanchéité des assemblages à bague Dichtheit von elastomeren Dichtringverbindungen (ISO
d'étanchéité en élastomère (ISO 13259:2018) 13259:2018)
This European Standard was approved by CEN on 19 April 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13259:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 13259:2018
EN ISO 13259:2018 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 13259:2018
EN ISO 13259:2018 (E)
European foreword
This document (EN ISO 13259:2018) has been prepared by Technical Committee ISO/TC 138 “Plastics
pipes, fittings and valves for the transport of fluids” in collaboration with Technical Committee
CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2018, and conflicting national standards
shall be withdrawn at the latest by December 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1277:2003.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuani
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.