EN 15632-2:2022
(Main)District heating pipes - Factory made flexible pipe systems - Part 2: Bonded system with plastic service pipes; requirements and test methods
District heating pipes - Factory made flexible pipe systems - Part 2: Bonded system with plastic service pipes; requirements and test methods
This document specifies requirements and test methods for flexible, factory made, buried district heating pipe systems with plastic service pipes and bonding between the layers of the pipe assemblies.
It is only applicable in conjunction with part 1.
This document is applicable to pipes, fittings, their joints and to joints with components made of non-plastics materials intended to be used for district heating installations.
This document is applicable to a maximum operating temperature of 95 °C and maximum operating design pressure up to 1,0 MPa for a design service life of at least 30 years.
This document does not apply to cover surveillance systems.
NOTE For higher temperatures or for the transport of other fluids, for example potable water, additional requirements and testing is needed. Such requirements are not specified in this document.
Fernwärmerohre - Werkmäßig gedämmte flexible Rohrsysteme - Teil 2: Verbundrohrsysteme mit Mediumrohren aus Kunststoff; Anforderungen und Prüfungen
Dieses Dokument legt Anforderungen und Prüfverfahren für flexible, werkmäßig hergestellte, erdverlegte Fernwärmerohrsysteme mit Mediumrohren aus Kunststoff und Verbund zwischen den Schichten der Rohrbaugruppen fest.
Es ist nur in Verbindung mit Teil 1 anwendbar.
Dieses Dokument gilt für Rohre, Formstücke, ihre Verbindungen untereinander sowie mit Rohrleitungsteilen, deren Werkstoffe nicht aus Kunststoff bestehen und die für Fernwärmeinstallationen vorgesehen sind.
Dieses Dokument ist für eine maximale Betriebstemperatur von 95 °C und einen zulässigen Betriebsdruck bis einschließlich 1,0 MPa für eine Auslegungsnutzungsdauer von mindestens 30 Jahren anwendbar.
Dieses Dokument gilt nicht für Überwachungssysteme.
ANMERKUNG Für höhere Temperaturen oder für den Transport anderer Flüssigkeiten, z. B. Trinkwasser, sind zusätzliche Anforderungen und Prüfungen erforderlich. Derartige Anforderungen sind in diesem Dokument nicht festgelegt.
Tuyaux de chauffage urbain - Systèmes de tuyaux flexibles manufacturés - Partie 2 : Système bloqué avec tubes de service en plastique ; exigences et méthodes d'essai
Le présent document spécifie les exigences et les méthodes d’essai relatives aux systèmes de tuyaux de chauffage urbain flexibles, manufacturés, enterrés, avec des tubes de service en plastique et une adhérence entre les couches des assemblages de tubes.
Il n'est utilisable que conjointement avec la partie 1.
Le présent document est applicable aux tuyaux, raccords, leurs joints, et aux joints avec des composants en matériaux non plastiques destinés à être utilisés pour les installations de chauffage urbain.
Le présent document est applicable à des températures maximales de service de 95 °C et des pressions de service maximales inférieures à 1,0 MPa, pour une durée de vie prévue d’au moins 30 ans.
Le présent document ne couvre pas les systèmes de surveillance.
NOTE Pour les températures plus élevées ou pour le transport d’autres fluides, par exemple, de l’eau potable, des exigences et des essais supplémentaires sont nécessaires. Ces exigences ne sont pas spécifiées dans le présent document.
Cevi za daljinsko ogrevanje - Tovarniško izdelani gibki cevni sistemi - 2. del: Vezani cevni sistemi iz polimernih materialov - Zahteve in preskusne metode
Ta evropski standard določa zahteve in preskusne metode za izolirane gibke podzemne
cevi za ogrevanje z delovnimi cevmi iz polimernih materialov z medsebojno vezanimi sloji.
Ta evropski standard se uporablja za najvišje obratovalne temperature do 95 °C in najvišje obratovalne
tlake do 10 barov za predvideno življenjsko dobo vsaj 30 let.
Ta evropski standard ne zajema nadzornih sistemov.
OPOMBA: Za višje temperature ali prevoz drugih tekočin, na primer pitne vode, so potrebni dodatne zahteve
in preskusi. Take zahteve niso določene v tem evropskem standardu.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 15632-2:2022
01-julij-2022
Nadomešča:
SIST EN 15632-2:2010+A1:2015
Cevi za daljinsko ogrevanje - Tovarniško izdelani gibki cevni sistemi - 2. del:
Vezani cevni sistemi iz polimernih materialov - Zahteve in preskusne metode
District heating pipes - Factory made flexible pipe systems - Part 2: Bonded system with
plastic service pipes; requirements and test methods
Fernwärmerohre - Werkmäßig gedämmte flexible Rohrsysteme - Teil 2:
Verbundrohrsysteme mit Mediumrohren aus Kunststoff; Anforderungen und Prüfungen
Tuyaux de chauffage urbain - Système de tuyaux flexibles pré-isolés - Partie 2 : Système
bloqué avec tubes de service en plastique ; exigences et méthodes d'essai
Ta slovenski standard je istoveten z: EN 15632-2:2022
ICS:
23.040.07 Cevovodi za daljinsko Pipeline and its parts for
ogrevanje in njihovi deli district heat
91.140.10 Sistemi centralnega Central heating systems
ogrevanja
SIST EN 15632-2:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 15632-2:2022
---------------------- Page: 2 ----------------------
SIST EN 15632-2:2022
EN 15632-2
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2022
EUROPÄISCHE NORM
ICS 23.040.07 Supersedes EN 15632-2:2010+A1:2014
English Version
District heating pipes - Factory made flexible pipe systems
- Part 2: Bonded system with plastic service pipes;
requirements and test methods
Tuyaux de chauffage urbain - Systèmes de tuyaux Fernwärmerohre - Werkmäßig gedämmte flexible
flexibles manufacturés - Partie 2 : Système bloqué avec Rohrsysteme - Teil 2: Verbundrohrsysteme mit
tubes de service en plastique ; exigences et méthodes Mediumrohren aus Kunststoff; Anforderungen und
d'essai Prüfungen
This European Standard was approved by CEN on 27 March 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15632-2:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 15632-2:2022
EN 15632-2:2022 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Classification . 7
4.1 Operating temperatures and service life. 7
4.2 Design pressures . 7
5 Requirements . 8
5.1 General requirements .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.