EN ISO 8062-1:2007

SLOVENSKI STANDARD
SIST EN ISO 8062-1:2007
01-julij-2007
1DGRPHãþD
SIST ISO 8062:1995
Specifikacije geometrijskih izdelkov - Dimenzijske in geometrijske tolerance
zaformanih delov – 1. del: Slovar (ISO 8062-1:2007)
Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for
moulded parts - Part 1: Vocabulary (ISO 8062-1:2007)
Geometrische Produktspezifikationen (GPS) - Maß-, Formund Lagetoleranzen für
Formteile - Teil 1: Begriffe (ISO 8062-1:2007)
Spécification géométrique des produits (GPS) - Tolérances dimensionnelles et
géométriques des pieces moulées - Partie 1: Vocabulaire (ISO 8062-1:2007)
Ta slovenski standard je istoveten z: EN ISO 8062-1:2007
ICS:
01.040.17 Meroslovje in merjenje. Metrology and measurement.
Fizikalni pojavi (Slovarji) Physical phenomena
(Vocabularies)
17.040.10 Tolerance in ujemi Limits and fits
17.040.40 6SHFLILNDFLMDJHRPHWULMVNLK Geometrical Product
YHOLþLQL]GHOND*36 Specification (GPS)
SIST EN ISO 8062-1:2007 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 8062-1:2007

---------------------- Page: 2 ----------------------

SIST EN ISO 8062-1:2007
EUROPEAN STANDARD
EN ISO 8062-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2007
ICS 17.040.10; 01.040.17

English Version
Geometrical product specifications (GPS) - Dimensional and
geometrical tolerances for moulded parts - Part 1: Vocabulary
(ISO 8062-1:2007)
Spécification géométrique des produits (GPS) - Tolérances Geometrische Produktspezifikationen (GPS) - Maß-, Form-
dimensionnelles et géométriques des pièces moulées - und Lagetoleranzen für Formteile - Teil 1: Begriffe (ISO
Partie 1: Vocabulaire (ISO 8062-1:2007) 8062-1:2007)
This European Standard was approved by CEN on 25 February 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8062-1:2007: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 8062-1:2007

EN ISO 8062-1:2007 (E)





Foreword


This document (EN ISO 8062-1:2007) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 190 "Foundry technology", the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by December 2007, and conflicting national
standards shall be withdrawn at the latest by December 2007.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.


Endorsement notice

The text of ISO 8062-1:2007 has been approved by CEN as EN ISO 8062-1:2007 without any
modifications.

2

---------------------- Page: 4 ----------------------

SIST EN ISO 8062-1:2007
INTERNATIONAL ISO

STANDARD 8062-1
NORME
First edition
Première édition
INTERNATIONALE
2007-06-01

Geometrical product specifications
(GPS) — Dimensional and geometrical
tolerances for moulded parts —
Part 1:
Vocabulary
Spécification géométrique des produits
(GPS) — Tolérances dimensionnelles et
géométriques des pièces moulées —
Partie 1:
Vocabulaire




Reference number
Numéro de référence
ISO 8062-1:2007(E/F)
©
 ISO 2007

---------------------- Page: 5 -----
...