Communication cables - Specifications for test methods - Part 3-8: Mechanical test methods - Abrasion resistance of cable sheath markings

This European Standard details the method of test to determine the ability of the sheath markings of a finished cable used in analogue and digital communication systems to withstand abrasion. It will be read in conjunction with EN 50289-3-1, which contains essential provisions for its application. Depending on the kind of marking and as indicated in the relevant cable specification, one of the following two methods will be used: - Method 1: is suitable for rigid marking types like embossing, indenting and sintering; - Method 2: is applicable to marking types other than embossing, indenting and sintering.

Kommunikationskabel - Spezifikationen für Prüfverfahren - Teil 3-8: Mechanische Prüfverfahren - Abriebfestigkeit der Markierung des Kabelmantels

Câbles de communication - Spécifications des méthodes d'essai - Partie 3-8: Méthodes d'essais mécaniques - Résistance à l'abrasion du marquage de la gaine

La présente Norme européenne spécifie la méthode d’essai à utiliser pour la détermination de l’aptitude du marquage de la gaine d’un câble complet utilisé dans les systèmes de communication analogiques et numériques à résister à l’abrasion. Elle doit être utilisée conjointement avec l’EN 50289-3-1 qui contient les dispositions essentielles pour son application. Suivant le type de marquage et les indications de la spécification correspondante, l’une des deux méthodes suivantes est utilisée: - Méthode 1: elle convient pour les types de marquage rigides en relief, en creux ou fritté; - Méthode 2: elle est applicable aux autres types de marquages.

Komunikacijski kabli - Specifikacije za preskusne metode - 3-8. del: Mehanske preskusne metode - Odpornost proti obrabi oznak na kabelskih plaščih

Ta evropski standard opisuje preskusno metodo za ugotavljanje odpornosti proti obrabi oznak na plašču dokončanega kabla, ki se uporablja v analognih in digitalnih komunikacijskih sistemih. Uporablja se v povezavi s standardom EN 50289-3-1, ki vsebuje bistvene določbe za njegovo uporabo. Odvisno od vrste oznak in navedb v ustrezni specifikaciji za kable se uporablja ena od naslednjih dveh metod: – metoda 1: primerna je za vrste togega označevanja, kot so reliefno žigosanje, vtiskovanje in sintranje; – metoda 2: primerna je za vrste oznak, razen za reliefno žigosanje, vtiskovanje in sintranje.

General Information

Status
Published
Publication Date
18-Nov-2013
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
08-Nov-2013
Due Date
13-Jan-2014
Completion Date
19-Nov-2013

Relations

Buy Standard

Standard
EN 50289-3-8:2014
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 50289-3-8:2014
01-januar-2014
1DGRPHãþD
SIST EN 50289-3-8:2002
.RPXQLNDFLMVNLNDEOL6SHFLILNDFLMH]DSUHVNXVQHPHWRGHGHO0HKDQVNH
SUHVNXVQHPHWRGH2GSRUQRVWSURWLREUDELR]QDNQDNDEHOVNLKSODãþLK
Communication cables - Specifications for test methods - Part 3-8: Mechanical test
methods - Abrasion resistance of cable sheath markings
Kommunikationskabel - Spezifikationen für Prüfverfahren - Teil 3-8: Mechanische
Prüfverfahren - Abriebfestigkeit der Markierung des Kabelmantels
Câbles de communication - Spécifications des méthodes d'essai - Partie 3-8: Méthodes
d'essais mécaniques - Résistance à l'abrasion du marquage de la gaine
Ta slovenski standard je istoveten z: EN 50289-3-8:2013
ICS:
33.120.10 Koaksialni kabli. Valovodi Coaxial cables. Waveguides
SIST EN 50289-3-8:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 50289-3-8:2014

---------------------- Page: 2 ----------------------

SIST EN 50289-3-8:2014

EUROPEAN STANDARD
EN 50289-3-8

NORME EUROPÉENNE
October 2013
EUROPÄISCHE NORM

ICS 33.120.10 Supersedes EN 50289-3-8:2001


English version


Communication cables -
Specifications for test methods -
Part 3-8: Mechanical test methods -
Abrasion resistance of cable sheath markings



Câbles de communication -  Kommunikationskabel -
Spécifications des méthodes d'essai - Spezifikationen für Prüfverfahren -
Partie 3-8: Méthodes d'essais mécaniques Teil 3-8: Mechanische Prüfverfahren -
- Abriebfestigkeit der Markierung des
Résistance à l'abrasion du marquage de Kabelmantels
la gaine






This European Standard was approved by CENELEC on 2013-09-16. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.


CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 50289-3-8:2013 E

---------------------- Page: 3 ----------------------

SIST EN 50289-3-8:2014
EN 50289-3-8:2013 - 2 -

Contents
Foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Test method . 4
4.1 Equipment . 4
4.1.1 Method 1 . 4
4.1.2 Method 2 . 4
4.2 Test sample . 4
4.3 Procedure . 5
4.3.1 Method 1 . 5
4.3.2 Method 2 . 5
4.4 Requirements . 5
5 Test report . 6

---------------------- Page: 4 ----------------------

SIST EN 50289-3-8:2014
- 3 - EN 50289-3-8:2013

Foreword
This document (EN 50289-3-8:2013) was prepared by CLC/TC 46X "Communication cables".
The following dates are fixed:
(dop) 2014-09-16
• latest date by which this document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2016-09-16
• latest date by which the national
standards conflicting with this
document have to be withdrawn
This document supersedes EN 50289-3-8:2001.
The abrasion resistance test in EN 50289-3-8 has been amended to include the following
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.