SIST EN IEC 63093-3:2021

SLOVENSKI STANDARD
SIST EN IEC 63093-3:2021
01-junij-2021
Nadomešča:
SIST EN 62323:2005
Feritna jedra - Smernice o merah in mejnih vrednostih površinskih nepravilnosti -
3. del: Feritna jedra v obliki polovičnih lončkov za induktivna bližinska stikala
Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 3:
Half pot-cores made of ferrite for inductive proximity switches
Ta slovenski standard je istoveten z: EN IEC 63093-3:2020
ICS:
29.100.10 Magnetne komponente Magnetic components
SIST EN IEC 63093-3:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 63093-3:2021

---------------------- Page: 2 ----------------------
SIST EN IEC 63093-3:2021


EUROPEAN STANDARD EN IEC 63093-3

NORME EUROPÉENNE

EUROPÄISCHE NORM
May 2020
ICS 29.100.10 Supersedes EN 62323:2005 and all of its amendments
and corrigenda (if any)
English Version
Ferrite cores - Guidelines on dimensions and the limits of
surface irregularities - Part 3: Half pot-cores made of ferrite for
inductive proximity switches
(IEC 63093-3:2020)
Noyaux ferrites - Lignes directrices relatives aux Ferritkerne - Richtlinien zu Maßen und Grenzen von
dimensions et limites des irrégularités de surface - Partie 3: Oberflächenschädigungen - Teil 3: Ferritschalenkernhälften
Demi-circuits magnétiques en pots en ferrite pour des für induktive Näherungsschalter
commutateurs inductifs de proximité (IEC 63093-3:2020)
(IEC 63093-3:2020)
This European Standard was approved by CENELEC on 2020-05-01. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 63093-3:2020 E

---------------------- Page: 3 ----------------------
SIST EN IEC 63093-3:2021
EN IEC 63093-3:2020 (E)
European foreword
The text of document 51/1300/CDV, future edition 1 of IEC 63093-3, prepared by IEC/TC 51
"Magnetic components, ferrite and magnetic powder materials" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 63093-3:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-02-01
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-05-01
document have to be withdrawn

This document supersedes EN 62323:2005 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 63093-3:2020 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 61332 NOTE Harmonized as EN 61332
IEC 62044-1 NOTE Harmonized as EN 62044-1
IEC 62044-2 NOTE Harmonized as EN 62044-2
IEC 62044-3 NOTE Harmonized as EN 62044-3
IEC 62317-1 NOTE Harmonized as EN 62317-1
IEC 62317-2 NOTE Harmonized as EN 62317-2


2

---------------------- Page: 4 ----------------------
SIST EN IEC 63093-3:2021
EN IEC 63093-3:2020 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60401-1 - Terms and nomenclature for cores made of - -
magnetically soft ferrites - Part 1: Terms used for
physical irregularities and reference of
dimensions
IEC 60424-1 2015 Ferrite cores - Guidelines on the limits of surface EN 60424-1 2016
irregularities - Part 1: General specification



3

---------------------- Page: 5 ----------------------
SIST EN IEC 63093-3:2021

---------------------- Page: 6 ----------------------
SIST EN IEC 63093-3:2021



IEC 63093-3

®


Edition 1.0 2020-03




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Ferrite cores – Guidelines on dimensions and the limits of surface

irregularities –

Part 3: Half pot-cores made of ferrite for inductive proximity switches




Noyaux ferrites – Lignes directrices relatives aux dimensions et limites

des irrégularités de surface –


Partie 3: Demi-circuits magnétiques en pots en ferrite pour des commutateurs

inductifs de proximité












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ISBN 978-2-8322-8009-6
ICS 29.100.10




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 63093-3:2021
– 2 – IEC 63093-3:2020 © IEC 2020
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Primary dimensions . 5
4.1 General . 5
4.2 Nomenclature of dimensions . 6
4.3 Dimensions of PS-cores . 7
4.4 Requirements . 8
4.5 Marking . 8
5 Limits of surface irregularities . 8
5.1 General . 8
5.2 Examples of surface irregularities . 8
5.3 Chips and ragged edges . 9
5.4 Cracks . 11
5.5 Pull-out, crystallite and pore locations for PS-cores . 12
5.6 Flash . 12
Bibliography . 14

Figure 1 – Fundamental types of PS-cores . 6
Figure 2 – Nomenclature of dimensions . 7
Figure 3 – Examples of surface irregularities . 9
Figure 4 – Chips and ragged edge on the surfaces . 9
Figure 5 – Cracks location – Top view . 11
Figure 6 – Cracks location – Bottom view . 11
Figure 7 – Pull-out, crystallite and pore locations . 12
Figure 8 – Flash location. 13
Figure 9 – Flash location in the wire hole . 13

Table 1 – Dimensions of PS-cores . 8
Table 2 – Area and length references of irregularities for visual inspection . 10
Table 3 – Limits for cracks . 12

---------------------- Page: 8 ----------------------
SIST EN IEC 63093-3:2021
IEC 63093-3:2020 © IEC 2020 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FERRITE CORES – GUIDELINES ON DIMENSIONS
AND THE LIMITS OF SURFACE IRREGULARITIES –

Part 3: Half pot-cores made of ferrite
for inductive proximity switches

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provi
...