Ships and marine technology — Marine evacuation systems — Testing under conditions of icing

This document provides specifications for a test of marine evacuation systems (MES) under conditions of icing in support of the requirement in paragraph 6.2.2.1.8 of the International Life-saving Appliance (LSA) Code.

Navires et technologie maritime — Systèmes d'évacuation maritimes — Conditions de prise de la glace

General Information

Status

Published

Publication Date

04-Jun-2019

ICS

47.020.01 - General standards related to shipbuilding and marine structures

Technical Committee

ISO/TC 8/SC 1 - Maritime safety

Drafting Committee

ISO/TC 8/SC 1/WG 1 - Lifesaving appliances and arrangements

Current Stage

9020 - International Standard under periodical review

Start Date

15-Apr-2024

Completion Date

15-Apr-2024

Ref Project

Buy Standard

ISO 19897:2019 - Ships and marine technology -- Marine evacuation systems -- Testing under conditions of icing

Standard

ISO 19897:2019 - Ships and marine technology -- Marine evacuation systems -- Testing under conditions of icing

English language

4 pages

sale 15% off

Preview

sale 15% off

Preview

Standards Content (Sample)

ISO 19897:2019 - Ships and mar...

INTERNATIONAL ISO
STANDARD 19897
First edition
2019-06
Ships and marine technology —
Marine evacuation systems — Testing
under conditions of icing
Navires et technologie maritime — Systèmes d'évacuation maritimes
— Conditions de prise de la glace
Reference number
ISO 19897:2019(E)
©
ISO 2019

---------------------- Page: 1 ----------------------
ISO 19897:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 19897:2019(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test arrangements and functions to be tested . 2
4.1 Deployment . 2
4.2 Stowage container . 2
4.3 Bowsing/retaining system . 2
4.4 Access to the passage . 2
5 Test procedure . 2
5.1 Ice accretion procedure . 2
5.2 Reference device . 3
Bibliography . 4
© ISO 2019 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 19897:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
d
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO

ISO 24569:2023(Main)

Ships and marine technology — External firefighting system test methods

This document specifies the test methods for marine external firefighting systems after installation aboard, mainly including test preparation, test conditions, test apparatus and procedures. This document excludes the performance requirements of the equipment. This document is applicable to the testing of external firefighting systems installed on ships for the purpose of extinguishing fires occurring on other vessels, offshore structures or quayside structures. This document applies to marine external firefighting system with water or foam as the medium.

Standard
8 pages
English language
sale 15% off

ISO

ISO 24409-4:2023(Main)

Ships and marine technology — Design, location and use of shipboard safety signs, fire control plan signs, safety notices and safety markings — Part 4: Escape plan signs used for general emergency information

This document establishes design principles for shipboard escape plan signs that contain information relevant to escape, embarkation, and fire safety, to be used for general information on board ships. These plans are intended to be displayed as signs in cabins and public areas, such as required by regulations. This document is not intended to cover the plans to be used by crew. The plans for crew are described in ISO 17631.

Standard
15 pages
English language
sale 15% off
Standard
16 pages
French language
sale 15% off

ISO

ISO 5476:2023(Main)

Ships and marine technology — Virtual reality and simulation training systems for lifesaving appliances and arrangements

This document provides general provisions and minimum criteria for using virtual reality and simulator equipment and systems instead of live training and drills with lifesaving appliances and arrangements, such as those required by SOLAS and MODU Code. This document is not intended to provide a generic training programme for the purposes of meeting International Convention on Standards of Training, Certification and Watchkeeping for Seafarers (STCW) requirements. This document serves to support the use of training devices (TD) onboard vessels that can deliver training and drills required by regulation, as well as additional non-obligatory training to crew. It is understood that training devices described in this document are used as an alternative to actual participation with and operations of lifesaving appliances (LSA) products during drills to meet mandatory training requirements.

Standard
16 pages
English language
sale 15% off
Standard
18 pages
French language
sale 15% off

ISO

ISO 17631:2022(Main)

Ships and marine technology — Shipboard plans for fire control, damage control, life-saving appliances and means of escape

This document specifies the content, type, design, layout and usage of shipboard and marine installation plans made available and displayed for fire control appliances and arrangements, damage control, lifesaving appliances and arrangements, and means of escape. It also specifies graphical symbols and illustrations used in such plans. It does not include signs and mimic signs that provide instructions for safe escape for general safety information.

Standard
28 pages
English language
sale 15% off

ISO

ISO 23678-1:2022(Main)

Ships and marine technology — Service personnel for the maintenance, thorough examination, operational testing, overhaul and repair of lifeboats and rescue boats, launching appliances and release gear — Part 1: General requirements for training providers

This document establishes a uniform, safe and consistent approach to training personnel to enable them to establish and maintain the required competencies in relation to maintenance, thorough examination, operational testing, overhaul and repair of lifeboats and rescue boats, launching appliances and release gear. It also provides the necessary information for interested parties to grant authorization and effectively evaluate and audit training, supporting the IMO Requirements, section 3. It describes the competence route, resources, facilities and certification requirements for personnel trained by a manufacturer or by an authorized service provider to carry out maintenance, thorough examination, operational testing, overhaul and repair of lifeboats (including free-fall lifeboats) and rescue boats (including fast rescue boats), launching appliances and release gear. This document also sets out the competence route of the candidate, and the resources that the training provider needs to deliver the training. This document is intended to be used in conjunction with ISO 23678-2, ISO 23678-3 and ISO 23678-4.

Standard
26 pages
English language
sale 15% off

ISO

ISO 23678-3:2022(Main)

This document establishes a uniform, safe and consistent approach to the technical training of personnel for the maintenance, thorough examination, operational testing, overhaul and repair of lifeboats and rescue boats, launching appliances and release gear. It also provides the necessary information for interested parties to grant authorization, effectively evaluate and audit training, supporting the IMO Requirements, section 3. It specifies the training requirements for the level 1 controlled environment education and technical training for personnel certified by a manufacturer or an authorized service provider to carry out maintenance, thorough examination, operational testing, overhaul and repair of lifeboats (including free-fall lifeboats) and rescue boats (including fast rescue boats), launching appliances and release gear. The level 1 training is split into two stages, both covered in this document: — stage 1 service technician technical controlled environment education and training has five modules that consist of classroom-based theory followed by practical sessions. The five modules encompass the scope and range of technical knowledge and skills required to assume type-specific design coverage of survival craft, release systems, davits and winches. The modules focus on supporting the requirements in the IMO Requirements, section 8, paragraphs 8.1, 8.2.1.1 to 8.2.1.6, 8.2.2, and 8.2.3. — stage 2 service technician technical controlled environment experience and assessment requires candidates to undertake a minimum of four supervised scenarios-based practical exercises assessments covering the range of type specific complete systems for which they will be certified. This document is intended to be used in conjunction with ISO 23678-1, ISO 23678-2 and ISO 23678-4. This document is applicable to the following types of lifeboats (including free-fall lifeboats), rescue boats (including fast rescue boats), launching appliances and release gear. Survival craft types: a) single fall totally enclosed lifeboats with sprinkler and air systems; b) twin fall totally enclosed lifeboats with sprinkler and air systems; c) partially enclosed lifeboats; d) tender lifeboats; e) freefall lifeboats; f) open lifeboat; g) inflatable rescue boats; h) rigid rescue boats; i) semi-ridged inflatable rescue boats; j) rigid fast rescue boats; k) rigid inflatable fast rescue boats. Survival craft propulsion system types: a) inboard diesel engines; b) outboard engines; c) propeller drives; d) jet drives. Davit types: a) gravity single and twin fall outrigger; b) hydraulic single pivoting/luffing; c) hydraulic multi pivot/luffing; d) telescopic; e) gravity roller track; f) gravity free fall primary; g) free fall hydraulic secondary; h) A-frame hydraulic; i) single arm slewing (manual, electric); j) davits with stored power systems. Winch types: a) twin drum; b) single drum; c) gravity-lowering, electric hoisting; d) gravity-lowering hydraulic hoisting; e) hydraulic hoisting and lowering. Hook release system types: a) on-load/off load (load not over centre); b) on-load/offload (load over centre); c) off load; d) freefall hydraulic; e) automatic off load.

Standard
41 pages
English language
sale 15% off

ISO

ISO 23678-4:2022(Main)

This document establishes a uniform, safe and consistent approach to the in-field competence assessment of personnel for the maintenance, thorough examination, operational testing, overhaul and repair of lifeboats and rescue boats, launching appliances and release gear. It also provides the necessary information for interested parties to grant authorization, effectively evaluate and audit training, supporting the IMO Requirements, section 3. It specifies the level 2 in-field initial and ongoing competence assessment for personnel certified by a manufacturer or an authorized service provider to carry out maintenance, thorough examination, operational testing, overhaul and repair of lifeboats (including free-fall lifeboats) and rescue boats (including fast rescue boats), launching appliances and release gear. The training an individual receives while following a development process is covered in ISO 23678-2 and ISO 23678-3. The competence requirements contained in this document provide a clear description of performance in-field in respect to: a) what practitioners are expected to do; b) the underpinning knowledge and skills they require to enable them to do what is expected; c) how they can demonstrate what is expected of them; d) how their performance can be assessed. This document is intended to be used in conjunction with ISO 23678-1, ISO 23678-2 and ISO 23678-3. This document is applicable to the following types of lifeboats (including free-fall lifeboats), rescue boats (including fast rescue boats), launching appliances and release gear. Survival craft types: a) single fall totally enclosed lifeboats with sprinkler and air systems; b) twin fall totally enclosed lifeboats with sprinkler and air systems; c) partially enclosed lifeboats; d) tender lifeboats; e) freefall lifeboats; f) open lifeboat; g) inflatable rescue boats; h) rigid rescue boats; i) semi-ridged inflatable rescue boats; j) rigid fast rescue boats; k) rigid inflatable fast rescue boats. Survival craft propulsion system types: a) inboard diesel engines; b) outboard engines; c) propeller drives; d) jet drives. Davit types: a) gravity single and twin fall outrigger; b) hydraulic single pivoting/luffing; c) hydraulic multi pivot/luffing; d) telescopic; e) gravity roller track; f) gravity free fall primary; g) free fall hydraulic secondary; h) A-frame hydraulic; i) single arm slewing (manual, electric); j) davits with stored power systems. Winch types: a) twin drum; b) single drum; c) gravity-lowering, electric hoisting; d) gravity-lowering hydraulic hoisting; e) hydraulic hoisting and lowering. Hook release system types: a) on-load/off load (load not over centre); b) on-load/offload (load over centre); c) off load; d) freefall hydraulic; e) automatic.

Standard
61 pages
English language
sale 15% off

ISO

ISO 23678-2:2022(Main)

This document establishes a uniform, safe and consistent approach to training and assessment of personnel to enable them to establish and maintain the required competencies in relation to maintenance, thorough examination, operational testing, overhaul and repair of lifeboats, rescue boats, launching appliances and release gear. It also provides the necessary information for interested parties to grant authorization and effectively evaluate and audit training, supporting the IMO Requirements, section 3. It specifies the initial training programme for personnel certified by a manufacturer or by an authorized service provider to carry out maintenance, thorough examination, operational testing, overhaul and repair of lifeboats (including free-fall lifeboats) and rescue boats (including fast rescue boats), launching appliances and release gear. This document specifies the training requirements for initial service technician training only. This document is intended to be used in conjunction with ISO 23678-1, ISO 23678-3 and ISO 23678-4. This document is applicable to the following types of lifeboats (including free-fall lifeboats), rescue boats (including fast rescue boats), launching appliances and release gear. — Survival craft types: a) single fall totally enclosed lifeboats with sprinkler and air systems; b) twin fall totally enclosed lifeboats with sprinkler and air systems; c) partially enclosed lifeboats; d) tender lifeboats; e) freefall lifeboats; f) open lifeboat; g) inflatable rescue boats; h) rigid rescue boats; i) semi-ridged inflatable rescue boats; j) rigid fast rescue boats; k) rigid inflatable fast rescue boats. — Survival craft propulsion system types: a) inboard diesel engines; b) outboard engines; c) propeller drives; d) jet drives. — Davit types: a) gravity single and twin fall outrigger; b) hydraulic single pivoting/luffing; c) hydraulic multi pivot/luffing; d) telescopic; e) gravity roller track; f) gravity free fall primary; g) free fall hydraulic secondary; h) A-frame hydraulic; i) single arm slewing (manual, electric); j) davits with stored power systems. — Winch types: a) twin drum; b) single drum; c) gravity lowering, electric hoisting; d) gravity lowering, hydraulic hoisting; e) hydraulic hoisting and lowering. — Hook release system types: a) on-load/off load (load not over centre); b) on-load/offload (load over centre); c) off load; d) freefall hydraulic; e) automatic off load.

Standard
23 pages
English language
sale 15% off

ISO

ISO 21195:2020(Main)

Ships and marine technology — Systems for the detection of persons while going overboard from ships (man overboard detection)

This document specifies technical requirements for systems designed to detect a person who has gone overboard from a ship. This document does not cover man overboard (MOB) detection systems that require the passengers or crew to wear or carry a device to trigger an MOB event.

Standard
15 pages
English language
sale 15% off

ISO

ISO 24409-1:2020(Main)

Ships and marine technology — Design, location and use of shipboard safety signs, fire control plan signs, safety notices and safety markings — Part 1: Design principles

This document specifies general design principles for shipboard safety signs, fire control plan signs, markings and notices intended to communicate safety-related information to persons on board ships.

Standard
18 pages
English language
sale 15% off