iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 19630:2021

(Main)

Fine ceramics (advanced ceramics, advanced technical ceramics) - Methods of test for reinforcements - Determination of tensile properties of filaments at ambient temperature (ISO 19630:2017)

Fine ceramics (advanced ceramics, advanced technical ceramics) - Methods of test for reinforcements - Determination of tensile properties of filaments at ambient temperature (ISO 19630:2017)

ISO 19630:2017 specifies the conditions for the determination of tensile properties of single filaments of ceramic fibre such as tensile strength, Young modulus and fracture strain. The method applies to continuous ceramic filaments taken from tows, yarns, braids and knittings, which have strain to fracture less than or equal to 5 %.
The method does not apply to carbon fibres that exhibit nonlinear stress-strain curve. The method does not apply to checking the homogeneity of strength properties of fibres, nor to assessing the effects of volume under stress. Statistical aspects of filament failure are not included.

Hochleistungskeramik - Verfahren zur Prüfung der Faserverstärkungen - Bestimmung der Zugeigenschaften von Endlosfasern bei Raumtemperatur (ISO 19630:2017)

Céramiques techniques - Méthodes d'essai pour renforts - Détermination des propriétés en traction du filament à température ambiante (ISO 19630:2017)

L'ISO 19630 :2017 spécifie les conditions de détermination des propriétés en traction d'un filament individuel de fibre céramique, comme la résistance en traction, le module de Young et la déformation à la rupture. La méthode s'applique à des filaments céramiques continus issus de mèches, fils, tresses et tricots ayant des déformations à la rupture inférieures ou égales à 5 %.
La méthode ne s'applique pas aux fibres de carbone qui présentent une courbe contrainte/déformation non linéaire. La méthode ne permet pas de contrôler l'homogénéité des propriétés de résistance des fibres, ni d'évaluer les effets de volume sous contrainte. Les aspects statistiques de la rupture des filaments ne sont pas traités dans cette norme.

Fina keramika (sodobna keramika, sodobna tehnična keramika) - Preskusne metode za ojačitve - Ugotavljanje nateznih lastnosti vlaken pri sobni temperaturi (ISO 19630:2017)

General Information

Status
Published
Publication Date
20-Jul-2021
Withdrawal Date
30-Jan-2022
ICS
81.060.30 - Advanced ceramics
Technical Committee
CEN/TC 184 - Advanced technical ceramics
Drafting Committee
CEN/TC 184/SC 1 - Ceramic composites
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
21-Jul-2021
Due Date
20-Feb-2023
Completion Date
21-Jul-2021
Ref Project
SIST EN ISO 19630:2021 - Fine ceramics (advanced ceramics, advanced technical ceramics) - Methods of test for reinforcements - Determination of tensile properties of filaments at ambient temperature (ISO 19630:2017)

Relations

Replaces
EN 1007-4:2004 - Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 4: Determination of tensile properties of filaments at ambient temperature
Effective Date
08-Jun-2022
Replaces
EN 1007-4:2004/AC:2007 - Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 4: Determination of tensile properties of filaments at ambient temperature
Effective Date
28-Jul-2021

Buy Standard

EN ISO 19630:2021EN ISO 19630:2021
PreviousNext
Standard
EN ISO 19630:2021
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 19630:2021
01-september-2021
Nadomešča:
SIST EN 1007-4:2004
SIST EN 1007-4:2004/AC:2007
Fina keramika (sodobna keramika, sodobna tehnična keramika) - Preskusne
metode za ojačitve - Ugotavljanje nateznih lastnosti vlaken pri sobni temperaturi
(ISO 19630:2017)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Methods of test for
reinforcements - Determination of tensile properties of filaments at ambient temperature
(ISO 19630:2017)
Hochleistungskeramik - Verfahren zur Prüfung der Faserverstärkungen - Bestimmung
der Zugeigenschaften von Endlosfasern bei Raumtemperatur (ISO 19630:2017)
Céramiques techniques - Méthodes d'essai pour renforts - Détermination des propriétés
en traction du filament à température ambiante (ISO 19630:2017)
Ta slovenski standard je istoveten z: EN ISO 19630:2021
ICS:
81.060.30 Sodobna keramika Advanced ceramics
SIST EN ISO 19630:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 19630:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 19630:2021


EN ISO 19630
EUROPEAN STANDARD

NORME EUROPÉENNE

July 2021
EUROPÄISCHE NORM
ICS 81.060.30 Supersedes EN 1007-4:2004
English Version

Fine ceramics (advanced ceramics, advanced technical
ceramics) - Methods of test for reinforcements -
Determination of tensile properties of filaments at ambient
temperature (ISO 19630:2017)
Céramiques techniques - Méthodes d'essai pour Hochleistungskeramik - Verfahren zur Prüfung der
renforts - Détermination des propriétés en traction du Faserverstärkungen - Bestimmung der
filament à température ambiante (ISO 19630:2017) Zugeigenschaften von Endlosfasern bei
Raumtemperatur (ISO 19630:2017)
This European Standard was approved by CEN on 11 July 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19630:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 19630:2021
EN ISO 19630:2021 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 19630:2021
EN ISO 19630:2021 (E)
European foreword
The text of ISO 19630:2017 has been prepared by Technical Committee ISO/TC 206 "Fine ceramics” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 19630:2021
by Technical Committee CEN/TC 184 “Advanced technical ceramics” the secretariat of which is held by
DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2022, and conflicting national standards shall
be withdrawn at the latest by January 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1007-4:2004.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Gr
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 26443:2023(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Rockwell indentation test for evaluation of adhesion of ceramic coatings (ISO 26443:2023)
SIST EN ISO 26443:2024

This document specifies a method for the qualitative evaluation of the adhesion of ceramic coatings up to 20 μm thick by indentation with a Rockwell diamond indenter. The formation of cracks after indentation can also reveal cohesive failure. The indentations are made with a Rockwell hardness test instrument.
The method described in this document can also be suitable for evaluating the adhesion of metallic coatings.
The test is not suitable for elastic coatings on hard substrates.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18755:2023(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of thermal diffusivity of monolithic ceramics by flash method (ISO 18755:2022)
SIST EN ISO 18755:2023

This document specifies the test method for the determination of thermal diffusivity from room temperature to at least 1 700 K by the flash method for homogeneous monolithic ceramics with porosity less than 10 %.
Flash methods, like laser flash, are applicable to homogeneous isotropic materials with thermal diffusivity values ranging from 0,1 to 1 000 mm2 s-1 within the temperature range from approximately 100 K to 2 300 K.
The method described in Annex G describes how to estimate, on the basis of the thermal diffusivity test, the specific heat capacity and the thermal conductivity of homogeneous monolithic ceramics with porosity less than 10 %.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 23739:2023(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Methods for chemical analysis of zirconium oxide powders (ISO 23739:2021)
SIST EN ISO 23739:2023

This document specifies methods for the chemical analysis of zirconium oxide powders used as the raw material for fine ceramics.
It stipulates the determination methods of the zirconium, aluminium, barium, calcium, cerium, cobalt, gadolinium, hafnium, iron, magnesium, potassium, silicon, sodium, strontium, titanium and yttrium contents in zirconium oxide powders for fine ceramics. The test sample is decomposed by acid pressure decomposition or alkali fusion. Contents of zirconium and yttrium are determined by using either a precipitation and gravimetric method or an inductively coupled plasma–optical emission spectrometry (ICP–OES) method. Contents of aluminium, barium, calcium, cerium, cobalt, gadolinium, hafnium, iron, magnesium, potassium, silicon, sodium, strontium and titanium are determined by using an ICP–OES method.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17947:2023(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Methods for chemical analysis of fine silicon nitride powders (ISO 17947:2014)
SIST EN ISO 17947:2023

This document specifies the methods for the chemical analysis of fine silicon nitride powders used as the raw material for fine ceramics. It stipulates the determination methods of total silicon, total nitrogen, aluminium, iron, calcium, oxygen, carbon, fluorine, and chlorine in fine silicon nitride powders.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 24370:2023(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for fracture toughness of monolithic ceramics at room temperature by chevron-notched beam (CNB) method (ISO 24370:2005)
SIST EN ISO 24370:2023

ISO 24370:2005 specifies a test method for determining the fracture toughness of monolithic ceramic materials at room temperature by the chevron-notched beam (CNB) method.
ISO 24370:2005 is applicable to monolithic ceramics and whisker- or particulate-reinforced ceramics that are regarded as macroscopically homogeneous. It is not applicable to continuous-fibre reinforced ceramic composites.
ISO 24370:2005 is usually applicable to ceramic materials with a fracture toughness less than about 12 megapascal(square root metre). The test method is applicable to materials with a flat crack-growth resistance curve and may be applicable to materials with a rising crack-growth resistance curve (R-curve).

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17092:2023(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of corrosion resistance of monolithic ceramics in acid and alkaline solutions (ISO 17092:2005)
SIST EN ISO 17092:2023

ISO 17092:2005 describes the test method for determining the corrosion resistance of fine ceramics in acid and alkaline solutions, such as sulfuric acid and sodium hydroxide. This International Standard is designed to provide an assessment of the mass changes and dimensional changes of test specimens following the corrosion test immersed in the corrosive liquids, and to assess whether corrosion has a significant effect on the subsequent strength. This test method may be used for development of materials, quality control, characterization, and design-data generation purposes.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 20509:2023(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of oxidation resistance of non-oxide monolithic ceramics (ISO 20509:2003)
SIST EN ISO 20509:2023

ISO 20509:2003 describes the method of test for determining the oxidation resistance of non-oxide monolithic ceramics, such as silicon nitride, sialon and silicon carbide at high temperatures. This International Standard is designed to provide an assessment of the mass and dimensional changes of test pieces following oxidation at high temperature in an oxidizing atmosphere, and to assess whether oxidation has a significant effect on the subsequent strength. This test method may be used for materials development, quality control, characterization, and design data generation purposes.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 20501:2022(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Weibull statistics for strength data (ISO 20501:2019)
SIST EN ISO 20501:2023

This document covers the reporting of uniaxial strength data and the estimation of probability distribution parameters for advanced ceramics which fail in a brittle fashion. The failure strength of advanced ceramics is treated as a continuous random variable. Typically, a number of test specimens with well-defined geometry are brought to failure under well-defined isothermal loading conditions. The load at which each specimen fails is recorded. The resulting failure stresses are used to obtain parameter estimates associated with the underlying population distribution.
This document is restricted to the assumption that the distribution underlying the failure strengths is the two-parameter Weibull distribution with size scaling. Furthermore, this document is restricted to test specimens (tensile, flexural, pressurized ring, etc.) that are primarily subjected to uniaxial stress states. Subclauses 6.4 and 6.5 outline methods of correcting for bias errors in the estimated Weibull parameters, and to calculate confidence bounds on those estimates from data sets where all failures originate from a single flaw population (i.e. a single failure mode). In samples where failures originate from multiple independent flaw populations (e.g. competing failure modes), the methods outlined in 6.4 and 6.5 for bias correction and confidence bounds are not applicable.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 20504:2022(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Mechanical properties of ceramic composites at room temperature - Determination of compressive properties (ISO 20504:2022)
SIST EN ISO 20504:2023

This document describes procedures for determination of the compressive behaviour of ceramic matrix composite materials with continuous fibre reinforcement at room temperature. This method applies to all ceramic matrix composites with a continuous fibre reinforcement, uni-directional (1D), bi-directional (2D) and tri-directional (xD, with 2 < x < 3), tested along one principal axis of reinforcement or off axis conditions. This method also applies to carbon-fibre-reinforced carbon matrix composites (also known as carbon/carbon or C/C). Two cases of testing are distinguished: compression between platens and compression using grips.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21814:2022(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Methods for chemical analysis of aluminium nitride powders (ISO 21814:2019)
SIST EN ISO 21814:2023

This document specifies methods for the chemical analysis of fine aluminium nitride powders used as the raw material for fine ceramics.
This document stipulates the determination methods of the aluminium, total nitrogen, boron, calcium, copper, iron, magnesium, manganese, molybdenum, nickel, potassium, silicon, sodium, titanium, tungsten, vanadium, zinc, zirconium, carbon, chlorine, fluorine, and oxygen contents in aluminium nitride powders. The aluminium content is determined by using either an acid pressure decomposition-CyDTA-zinc back titration method or an acid digestion-inductively coupled plasma-optical emission spectrometry (ICP-OES) method. The total nitrogen content is determined by using an acid pressure decomposition-distillation separation-acidimetric titration method, a direct decomposition-distillation separation-acidimetric titration method, or an inert gas fusion-thermal conductivity method. The boron, calcium, copper, iron, magnesium, manganese, molybdenum, nickel, potassium, silicon, sodium, titanium, tungsten, vanadium and zinc contents are determined by using an acid digestion-ICP-OES method or an acid pressure decomposition-ICP-OES method. The sodium and potassium contents are determined via an acid pressure decomposition-flame emission method or an acid pressure decomposition-atomic absorption spectrometry method. The oxygen content is determined by using an inert gas fusion-IR absorption spectrometry method, while that of carbon is determined via a combustion-IR absorption spectrometry method or a combustion-conductometry method. The chlorine and fluorine contents are determined by using a pyrohydrolysation method followed by ion chromatography or spectrophotometry.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day