iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 13257:2017

(Main)

Thermoplastics piping systems for non-pressure applications - Test method for resistance to elevated temperature cycling (ISO 13257:2010)

Thermoplastics piping systems for non-pressure applications - Test method for resistance to elevated temperature cycling (ISO 13257:2010)

ISO 13257:2010 specifies a method for testing the resistance of thermoplastics piping systems for soil and waste discharge inside buildings, application area "B", or buried in the ground within the building structure, application areas "BD" or "UD", to 1 500 cycles of elevated temperature cycling.

Rohrleitungssysteme aus Thermoplasten für drucklose Anwendungen - Prüfverfahren für die Temperaturbeanspruchbarkeit (ISO 13257:2010)

Systèmes de canalisations thermoplastiques pour applications sans pression - Méthode d'essai de résistance à des cycles de température élevée (ISO 13257:2010)

L'ISO 13257:2010 spécifie une méthode d'essai de résistance des systèmes de canalisations thermoplastiques pour l'évacuation des eaux usées et eaux-vannes à l'intérieur des bâtiments, zone d'application «B», ou enterrées sous le bâtiment, zones d'application «BD» ou «UD», à 1 500 cycles à une température élevée.

Plastomerni cevni sistemi, ki delujejo po težnostnem principu - Metoda za preskus odpornosti proti zvišani temperaturi (ISO 13257:2010)

Standard ISO 13257:2010 določa metodo za preskušanje odpornosti plastomernih cevnih odvodnih sistemov v zgradbah (območje uporabe »B«) ali vkopanih v zemljo znotraj stavbne konstrukcije (območje uporabe »BD« ali »UD«), ko so izpostavljeni 1500 ciklom krožeče povišane temperature.

General Information

Status
Withdrawn
Publication Date
17-Oct-2017
Withdrawal Date
11-Dec-2018
ICS
23.040.20 - Plastics pipes
23.040.45 - Plastics fittings
91.140.80 - Drainage systems
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
12-Dec-2018
Ref Project
SIST EN ISO 13257:2018 - Thermoplastics piping systems for non-pressure applications - Test method for resistance to elevated temperature cycling (ISO 13257:2010)

Relations

Replaces
EN 1055:1996 - Plastics piping systems - Thermoplastics piping systems for soil and waste discharge inside buildings - Test method for resistance to elevated temperature cycling
Effective Date
19-Oct-2016
Replaced By
EN ISO 13257:2018 - Thermoplastics piping systems for non-pressure applications - Test method for resistance to elevated temperature cycling (ISO 13257:2018)
Effective Date
19-Dec-2018

Buy Standard

EN ISO 13257:2018EN ISO 13257:2018
PreviousNext
Standard
EN ISO 13257:2018
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 13257:2018
01-januar-2018
1DGRPHãþD
SIST EN 1055:1997
Plastomerni cevni sistemi, ki delujejo po težnostnem principu - Metoda za preskus
odpornosti proti zvišani temperaturi (ISO 13257:2010)
Thermoplastics piping systems for non-pressure applications - Test method for
resistance to elevated temperature cycling (ISO 13257:2010)
Rohrleitungssysteme aus Thermoplasten für drucklose Anwendungen - Prüfverfahren für
die Temperaturbeanspruchbarkeit (ISO 13257:2010)
Systèmes de canalisations thermoplastiques pour applications sans pression - Méthode
d'essai de résistance à des cycles de température élevée (ISO 13257:2010)
Ta slovenski standard je istoveten z: EN ISO 13257:2017
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
SIST EN ISO 13257:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 13257:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 13257:2018


EN ISO 13257
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2017
EUROPÄISCHE NORM
ICS 23.040.20; 91.140.80 Supersedes EN 1055:1996
English Version

Thermoplastics piping systems for non-pressure
applications - Test method for resistance to elevated
temperature cycling (ISO 13257:2010)
Systèmes de canalisations thermoplastiques pour Rohrleitungssysteme aus Thermoplasten für drucklose
applications sans pression - Méthode d'essai de Anwendungen - Prüfverfahren für die
résistance à des cycles de température élevée (ISO Temperaturbeanspruchbarkeit (ISO 13257:2010)
13257:2010)
This European Standard was approved by CEN on 19 September 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13257:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 13257:2018
EN ISO 13257:2017 (E)
Contents Page
European Foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 13257:2018
EN ISO 13257:2017 (E)
European Foreword
The text of ISO 13257:2010 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes,
fittings and valves for the transport of fluids” of the International Organization for Standardization
(ISO) and has been taken over as EN ISO 13257:2017 by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2018 and conflicting national standards shall be
withdrawn at the latest by October 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1055:1996.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
Endorsement notice
The t
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 13268:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness (ISO 13268:2022)
SIST EN ISO 13268:2023

This document specifies a test method for assessing the initial (short-term) tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13267:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance (ISO 13267:2022)
SIST EN ISO 13267:2023

This document specifies methods of test for the resistance of the base of thermoplastics inspection chambers and manholes to external soil and ground-water pressure after installation.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13266:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading (ISO 13266:2022)
SIST EN ISO 13266:2023

This document specifies a method of testing the resistance of the upper assembly of inspection chambers and manhole components against surface and traffic loading.
It is not applicable to requirements for testing the cover and frame. Those requirements are specified in EN 124-1 or other standards, depending on the material.
NOTE    Upper assembly components normally include shafts or risers, cones, telescopic adapters and near surface components.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11296-4:2018/A1:2021(Amendment)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes - Amendment 1: Updated definitions, marking requirements and procedure for alternative expression of flexural test results (ISO 11296-4:2018/Amd 1:2021)
SIST EN ISO 11296-4:2018/A1:2021

2021-02-11 - TC decision is missing to skip FV.

  • Amendment
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11296-7:2019(Main)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 7: Lining with spirally-wound pipes (ISO 11296-7:2019)
SIST EN ISO 11296-7:2019

This document, in conjunction with ISO 11296-1, specifies requirements and test methods for pipes which are formed on site by spirally winding and jointing a pre-manufactured profiled plastics strip, or a profiled plastics strip and integral locking joiner strip, and used for the renovation of underground non-pressure drainage and sewerage networks.
It applies to spirally-wound pipes of fixed or variable diameter made of profiled plastics strips, with or without steel stiffening elements, and installed by one of two methods.
The first method employs a dedicated winding machine in front of the open end of an existing pipeline, e.g. in a manhole. The pipes thus formed are simultaneously inserted into the existing pipeline by the winding forces, and by certain techniques can also be expanded in diameter after or during insertion.
The second method employs a dedicated winding machine which forms the pipe as it traverses the existing pipeline from one manhole to the next.
It applies to profiled plastics strips of unplasticized poly(vinyl chloride) (PVC U) with integral locking mechanism, or of high density polyethylene (HDPE) with integrally welded joints.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11297-3:2018(Main)
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 3: Lining with close-fit pipes (ISO 11297-3:2018)
SIST EN ISO 11297-3:2018

This document, in conjunction with ISO 11297‑1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of underground drainage and sewerage networks under pressure.
It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipes of either solid wall single layer or co-extruded layer construction, which is reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe liner, as well as associated fittings and joints for the construction of the lining system. It is not applicable to PE coated pipes having a peelable, contiguous, thermoplastic additional layer on the outside of the pipe.
It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature.
NOTE       For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427‑1:2007, Annex A.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11296-3:2018(Main)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2018)
SIST EN ISO 11296-3:2018

This document, in conjunction with ISO 11296‑1, specifies requirements and test methods for close-fit lining systems used for the renovation of underground non-pressure drainage and sewerage networks.
It applies to pipes and fittings made of polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC‑U) as manufactured, as well to the installed lining system with its associated joints.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21225-2:2018(Main)
Plastics piping systems for the trenchless replacement of underground pipeline networks - Part 2: Replacement off the line by horizontal directional drilling and impact moling (ISO 21225-2:2018)
SIST EN ISO 21225-2:2018

ISO 21225-2:2018 specifies requirements and test methods for pipes and fittings which are part of plastics piping systems for the trenchless replacement of various underground pipeline networks, underground non-pressure and pressure drainage and sewerage networks and underground water and gas supply networks, by means of horizontal directional drilling and impact moling.
ISO 21225-2:2018 is applicable to polyethylene (PE) pipes and fittings, as manufactured, as well as to the installed replacement system.
ISO 21225-2:2018 is intended to be used in conjunction with standards applicable for the construction of PE pipeline systems where available.
Regarding manufactured pipes it is applicable to three different PE pipe types:
-      PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes;
-      PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating;
-      PE pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe ("coated pipe"), see Annex A.
In addition, ISO 21225-2:2018 is applicable to:
-      jointing of pipe lengths by means of butt fusion joint to form continuous strings prior to installation;
-      fabricated and injection-moulded fittings made of PE.
Pipes made from other plastics, e.g. polypropylene (PP) are outside the scope of this document.
ISO 21225-2:2018 is not applicable to push-fit jointed discrete pipes assembled as part of the trenchless installation process.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21225-1:2018(Main)
Plastics piping systems for the trenchless replacement of underground pipeline networks - Part 1: Replacement on the line by pipe bursting and pipe extraction (ISO 21225-1:2018)
SIST EN ISO 21225-1:2018

ISO 21225-1:2018 specifies requirements and test methods for pipes and fittings which are part of plastics piping systems for the trenchless replacement of underground non-pressure and pressure drainage and sewerage networks and underground water and gas supply networks, by means of pipe bursting and pipe extraction.
ISO 21225-1:2018 is applicable to polyethylene (PE) pipes and fittings, as manufactured, as well as to the installed replacement system.
ISO 21225-1:2018 is intended to be used in conjunction with standards applicable for the construction of PE pipeline systems where available.
Regarding manufactured pipes it is applicable to three different PE pipe types:
-      PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes;
-      PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating;
-      PE pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe ("coated pipe"), see Annex A.
In addition, ISO 21225-1:2018 is applicable to:
-      jointing of pipe lengths by means of butt fusion joint;
-      jointing of pipe lengths by means of electrofusion joint;
-      fabricated and injection-moulded fittings made of PE.
Pipes made from other plastics, e.g. glass reinforced plastics (GRP), are outside the scope of this document.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11297-1:2018(Main)
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 1: General (ISO 11297-1:2018)
SIST EN ISO 11297-1:2018

ISO 11297-1:2018 specifies the requirements and test methods for plastics piping systems intended to be used for the renovation of underground drainage and sewerage networks under pressure, including both hydraulically and pneumatically pressurized systems. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is not applicable to the existing pipeline or any non-structural sprayed coatings or annular filler.
ISO 11297-1:2018 gives the general requirements co

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day