EN 12390-17:2019
(Main)Testing hardened concrete - Part 17: Determination of creep of concrete in compression
Testing hardened concrete - Part 17: Determination of creep of concrete in compression
This document describes the procedure for determining the creep (total creep, basic creep and drying creep) of hardened concrete test specimens subjected to a sustained longitudinal compressive load.
The test is suitable for specimens having a declared value of D of the coarsest fraction of aggregates actually used in the concrete (Dmax) not greater than 32 mm.
Prüfung von Festbeton - Teil 17: Bestimmung des Kriechens von Beton unter Druckspannung
Dieses Dokument beschreibt das Verfahren zur Bestimmung des Kriechens (Gesamtkriechen, Grundkriechen und Trocknungskriechen) von Probekörpern aus Festbeton, die einer andauernden Längsdruck¬beanspruchung ausgesetzt sind.
Die Prüfung ist geeignet für Probekörper mit einem Nennwert D des Größtkorns der tatsächlich im Beton verwendeten Gesteinskörnung (Dmax) von höchstens 32 mm.
Essais pour béton durci - Partie 17 : Détermination du fluage du béton en compression
Le présent document décrit le mode opératoire pour déterminer le fluage (fluage total, fluage propre et fluage de dessiccation) d’éprouvettes de béton durci soumises à une charge de compression longitudinale prolongée.
L’essai est adapté aux éprouvettes ayant une valeur déclarée D de la partie la plus grosse des granulats réellement utilisés dans le béton (Dmax) ne dépassant pas 32 mm.
Preskušanje strjenega betona - 17. del: Določanje lezenja betona pod tlakom
Ta dokument opisuje postopek za določanje lezenja (skupnega, avtogenega (osnovnega) in v času sušenja) preskušancev iz strjenega betona, ki so podvrženi trajni vzdolžni tlačni obremenitvi. Preskus je primeren za preskušance, pri katerih je deklarirana vrednost D najbolj grobega agregata, ki je dejansko uporabljen v betonu (Dmax), največ 32 mm.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 12390-17:2019
01-december-2019
Preskušanje strjenega betona - 17. del: Določanje lezenja betona pod tlakom
Testing hardened concrete - Part 17: Determination of creep of concrete in compression
Prüfung von Festbeton - Teil 17: Bestimmung des Kriechens von Beton unter
Druckspannung
Essais pour béton durci - Partie 17 : Détermination du fluage du béton en compression
Ta slovenski standard je istoveten z: EN 12390-17:2019
ICS:
91.100.30 Beton in betonski izdelki Concrete and concrete
products
SIST EN 12390-17:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 12390-17:2019
---------------------- Page: 2 ----------------------
SIST EN 12390-17:2019
EN 12390-17
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 91.100.30
English Version
Testing hardened concrete - Part 17: Determination of
creep of concrete in compression
Essais pour béton durci - Partie 17 : Détermination du Prüfung von Festbeton - Teil 17: Bestimmung des
fluage du béton en compression Kriechens von Beton unter Druckspannung
This European Standard was approved by CEN on 19 August 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12390-17:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 12390-17:2019
EN 12390-17:2019 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 7
5 Apparatus . 7
6 Test specimens . 10
7 Procedure. 10
8 Calculation of creep (total creep, basic creep and drying creep) . 13
9 Test report . 14
10 Precision . 15
Bibliography . 16
2
---------------------- Page: 4 ----------------------
SIST EN 12390-17:2019
EN 12390-17:2019 (E)
European foreword
This document (EN 12390-17:2019) has been prepared by Technical Committee CEN/TC 1
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.