EN 13480-2:2002/A2:2010
(Amendment)Metallic industrial piping - Part 2: Materials
Metallic industrial piping - Part 2: Materials
This part of EN 13480 covers the requirements for materials (including clad materials) for industrial piping and supports covered by EN 13480-1 constructed of metallic materials and is currently limited to steels with sufficient ductility below the creep range. It specifies the assessment of compliance for these materials. It also provides rules for the establishment of technical delivery conditions for materials for industrial piping.
Metallische industrielle Rohrleitungen - Teil 2: Werkstoffe
Tuyauteries industrielles métalliques - Partie 2: Matériaux
Kovinski industrijski cevovodi - 2. del: Materiali - Dopolnilo A2
Amandma A2:2011 je dodatek k standardu SIST EN 13480-2:2002.
Ta del EN 13480 zajema zahteve za materiale (vključno z obloženimi materiali) za industrijske cevovode in podpore, ki jih zajema EN 13480-1, narejene iz kovinskih materialov, in je trenutno omejen na jekla z zadostno preoblikovalnostjo pod razponom lezenja. Določa ocenjevanje skladnosti za te materiale. Zagotavlja tudi pravila za vzpostavitev tehničnih pogojev dostave materialov za industrijske cevovode.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13480-2:2002/A2:2011
01-junij-2011
Kovinski industrijski cevovodi - 2. del: Materiali - Dopolnilo A2
Metallic industrial piping - Part 2: Materials
Metallische industrielle Rohrleitungen - Teil 2: Werkstoffe
Tuyauteries industrielles métalliques - Partie 2: Matériaux
Ta slovenski standard je istoveten z: EN 13480-2:2002/A2:2010
ICS:
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
SIST EN 13480-2:2002/A2:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13480-2:2002/A2:2011
---------------------- Page: 2 ----------------------
SIST EN 13480-2:2002/A2:2011
EUROPEAN STANDARD
EN 13480-2:2002/A2
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2010
ICS 23.040.01
English Version
Metallic industrial piping - Part 2: Materials
Tuyauteries industrielles métalliques - Partie 2: Matériaux Metallische industrielle Rohrleitungen - Teil 2: Werkstoffe
This amendment A2 modifies the European Standard EN 13480-2:2002; it was approved by CEN on 16 April 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13480-2:2002/A2:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13480-2:2002/A2:2011
EN 13480-2:2002/A2:2010 (E)
Contents Page
Foreword .3
Foreword .4
2 Normative references .4
Annex B (normative) Requirements for prevention of brittle fracture at low temperatures .6
B.1 General .6
B.2 Material selection and impact energy requirements .7
B.2.1 Method 1 .7
B.2.2 Method 2 . 15
B.2.3 Method 3 — Fracture mechanics analysis . 27
B.3 General test requirements . 28
B.3.1 General . 28
B.3.2 Sub-sized specimens . 29
B.4 Welds . 30
B.4.1 General . 30
B.4.2 Welding procedure qualification . 30
B.4.3 Prod
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.