This document specifies the technical requirements for carbon steel and low-alloy steel forged flanges for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. This document applies to weldneck and blind flanges (full face, raised face, and RTJ groove) as well as anchor, swivel-ring flanges and orifice flanges. This document designates those categories of flanges that meet the industry's need to match ISO 3183 pipe. These flanges are for normal and low-temperature service and include supplementary requirements where required for sour service. Materials for, or the attachment of, factory-welded extensions, bolting materials, gaskets, slip-on flanges or flanged fittings are not covered by this document. This document is not applicable to integrally cast or forged flanges for valves, pumps or other equipment. This document does not cover the selection of the flange category or pressure class. Sizes and pressure classes listed in ISO 7005-1 and applicable to this document are as follows: — DN 10 (NPS 1/2) to DN 1500 (NPS 60); — PN 20 (class 150), PN 50 (class 300), PN 100 (class 600), PN 150 (class 900), PN 250 (class 1500), PN 420 (class 2500).

  • Standard
    18 pages
    English language
    sale 15% off
  • Draft
    18 pages
    English language
    sale 15% off

This document specifies the technical delivery conditions for unalloyed or low-alloy steel seamless and welded pipeline fittings for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. This document is applicable to welding-end fittings such as elbows, caps, tees, single or multiple extruded headers, reducers, and transition sections made from seamless and welded pipe of unalloyed or low-alloy steels. This document specifies two classes of fitting one related to material used in non-sour service and one for material to be use in sour service environment as shown in Table 1. This document is not applicable to the selection of the fitting class. This document is not applicable to the materials for, or the attachment of, factory-welded extensions.

  • Standard
    27 pages
    English language
    sale 15% off
  • Draft
    27 pages
    English language
    sale 15% off

This document establishes the general principles for the evaluation and minimization of the effects of stray current corrosion on external surfaces of buried or immersed pipeline systems caused by AC and DC electrical interference. Other stray current effects such as overheating, and interference with welding operations are not covered in this document. A brief description of AC effects, general principles and some guidelines, are provided. NOTE 1 See ISO 18086 for the effects of alternating current on buried or immersed pipelines. Systems that can also be affected by stray currents include buried or immersed metal structures such as the following: a) pipeline systems; b) metal sheathed cables; c) tanks and vessels; d) earthing systems; e) steel reinforcement in concrete; f) sheet steel piling. This document gives guidelines for — the design of cathodic protection systems that might produce stray currents, — the design of pipeline systems, or elements of pipeline systems, which are buried or immersed, and which can be subject to stray current corrosion, and — the selection of appropriate protection or mitigation measures. Internal corrosion risks from stray currents are not dealt with in detail in this document but principles and measures described here can be applicable for minimizing the interference effects. NOTE 2 The impact of electromagnetic interference on above-ground appurtenances of pipeline systems is covered in EN 50443, IEC 61140, IEC 60364-4-41, IEC 60479-1, IEC 60364-5-52, IEC/TS 61201 and IEC/TR 60479-5. This document can also be used for pipeline systems outside of the petrochemical and natural gas industries and other buried or immersed structures. NOTE 3 EN 50162 provides guidance for railway related structures.

  • Standard
    67 pages
    English language
    sale 15% off
  • Standard
    72 pages
    French language
    sale 15% off
  • Draft
    68 pages
    English language
    sale 15% off
  • Draft
    68 pages
    English language
    sale 15% off
  • Draft
    72 pages
    French language
    sale 15% off

This document specifies requirements for the manufacture of two product specification levels (PSL 1 and PSL 2) of seamless and welded steel pipes for use in pipeline transportation systems in the petroleum and natural gas industries. This document supplements API Spec 5L, 46th edition (2018), the requirements of which are applicable with the exceptions specified in this document. This document is not applicable to cast pipe.

  • Standard
    23 pages
    English language
    sale 15% off
  • Standard
    23 pages
    English language
    sale 15% off
  • Standard
    24 pages
    French language
    sale 15% off

This document specifies the technical delivery conditions for bends made by the cold bending process for bend with radii 5xOD or higher for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. This document also specifies the requirements for the manufacture of two product specification levels (PSLs) of cold bends corresponding to product specification levels given for pipe in ISO 3183. This document is applicable to cold bends made from seamless and welded pipe of unalloyed or low-alloy steels. NOTE 1 These are typically C-Mn steels or low-alloy steels that are appropriate for the corresponding level and grade of line pipe in accordance with ISO 3183. This document is not applicable to the selection of the cold bend product specification level. It is the responsibility of the purchaser to specify the PSL, based upon the intended use and design requirements. NOTE 2 See also ISO 3183:2012, Introduction. This document is not applicable to field cold bends and pipeline bends made by other manufacturing processes.

  • Standard
    31 pages
    English language
    sale 15% off

This document specifies requirements and gives recommendations on the management of geohazard risks during the pipeline design, construction and operational periods. This document is applicable to all operators and pipelines (existing and proposed/under construction). This document applies to onshore gathering and transmission pipelines used in the petroleum and natural gas industries. NOTE This document is not applicable to piping and pipelines within well-defined plants and facilities, such as pump or compressor stations, processing facilities or refineries. It is assumed that the facility site as a whole will be subject to a separate geohazard assessment to evaluate applicable natural and man-made hazards. Nevertheless, this document can provide useful guidance for assessing the geohazard threat to facilities, including the pipelines within the facility. This document is applicable to all reasonable and credible natural hazards induced by natural forces and hazards induced by human activity that manifest similarly to natural hazards collectively referred to as "geological hazards" or "geohazards", or through industry as attributed to "natural forces". Geohazards covered by this document include, but are not limited to (not given in order of significance): — mass wasting processes, including landslides, lateral spreads, rockfalls, debris flows, avalanches, and similar processes whether naturally occurring or anthropogenic; — land subsidence and/or sinkhole formation, whether naturally occurring such as from dissolution of salt or carbonate rock formations (karst formation) or human caused, such as from underground mining or withdrawal of subsurface fluids such as groundwater and oil and gas; — seismic hazards, such as ground shaking, fault rupture, liquefaction, flow failures and lateral spreading or associated secondary effects, such as seismically triggered landslides; — volcanic hazards, such as lahars, pyroclastic flows, lava flows, dam break, and volcanically induced seismicity (excluding ashfall), where such hazards can be reasonably predicted; — hydrologic processes, such as flooding, vertical scour of river bottoms, channel migration and bank erosion, channel avulsion, rapid lake drainage; — permafrost/periglacial processes and geothermal effects, such as thermal degradation, frost heave or thaw settlement, thermal erosion, thermokarst; — surface (overland), trench backfill, or earthwork fill erosion; — expansion or collapsing processes caused by expansive and collapsible soils, such as glaciomarine clays, collapsible loess, etc. This document is not applicable to atmospheric/environmental effects, such as the following: — high winds induced from hurricanes and tornadoes and similar storms, except where such events are reasonably predictable and will induce geohazards such as landslides, erosion, etc.; — lightning; — forest or brush fires; — ashfall from volcanic eruptions. Furthermore, this document is not applicable to cascading events, where one remote event leads to a chain of events that eventually induces a geohazard near the pipeline. It is only applicable to geohazards that directly affect the pipeline or RoW.

  • Standard
    67 pages
    English language
    sale 15% off
  • Standard
    71 pages
    French language
    sale 15% off

This document specifies requirements and gives recommendations on the management of integrity of a pipeline system throughout its life cycle, which includes design, construction, commissioning, operation, maintenance and abandonment. This document is applicable to offshore pipelines for transporting petroleum and natural gas. It is applicable to rigid steel pipelines. It is not applicable to flexible pipelines, dynamic risers or those constructed from other materials, such as glass-reinforced plastics. NOTE 1 An offshore pipeline system extends to: — the first valve, flange or connection above water on platform or subsea mechanical connector with subsea structure (i.e. manifold or dynamic riser); — the connection point to the offshore installation (i.e. piping manifolds are not included); — the first valve, flange, connection or isolation joint at a landfall, unless otherwise specified by the onshore legislation. NOTE 2 The components mentioned above (valve, flange, connection, isolation joint) include also any pup pieces, i.e. the offshore pipeline system extends to the weld beyond the pup piece, see Figure 1. This document is used for integrity management, which is initiated at the design and construction stage of the pipeline. Where requirements of a design and construction standard (e.g. ISO 13623) are different, the provisions of this document will enhance the design and construction from an integrity perspective.

  • Standard
    91 pages
    English language
    sale 15% off
  • Standard
    97 pages
    French language
    sale 15% off

1.1 This document specifies requirements and gives recommendations on the management of integrity of a pipeline system throughout its life cycle which includes design, construction, commissioning, operation, maintenance and abandonment. 1.2 This document is applicable to onshore pipeline systems used in transportation in the petroleum and natural gas industries, connecting wells, production plants, process plants, refineries and storage facilities, including any section of a pipeline constructed within the boundaries of such facilities for connection purposes. The extent of pipeline systems covered by this document is illustrated in Figure 1. This document does not deal specifically with the integrity of non-pipe elements. The pipeline segment between the wellsite and the gathering station, treatment plant or process plant (between Facilities 1 and 2 in Figure 1) is included in this document, though many mandatory elements of this document are not practical due to characteristics such as diameter, operating parameters, etc. 1.3 This document applies to rigid, steel pipelines. It is not applicable for flexible pipelines or those constructed from other materials, such as glass-reinforced plastics. 1.4 This document does not cover all conditions nor engineers' competency which might be related to pipeline integrity. The user can evaluate whether additional requirements are necessary. 1.5 This document is used for integrity management, which is initiated at the design and construction stage of the pipeline. Where requirements of a design and construction standard (e.g. ISO 13623) are different, the provisions of this document will enhance the design and construction from an integrity perspective.

  • Standard
    108 pages
    English language
    sale 15% off
  • Standard
    119 pages
    French language
    sale 15% off

This document specifies the criteria and requirements for the in-field application of coatings, coating repair and coating rehabilitation on buried pipelines. This document specifies: — coating assessment (new and existing); — removal of degraded coatings; — surface preparation; — on site or in situ application of external coatings. It is applicable to petroleum or natural gas pipelines, with or without a cathodic protection system. The pipelines could be operational during the removal, preparation and application process. This document states qualification/testing for field contractors and site applied coatings to all of the pipeline components, including bends, tees, fittings, valves and interfaces between different coatings in soil-to-air pipeline sections. Technical and performance characteristics of the repair and rehabilitation coating materials are referenced to ISO 21809-3. The coating of field joints is outside the scope of this document. Field joint coatings are dealt with in ISO 21809-3. This document excludes the application of coatings when the pipeline is immersed (submerged).

  • Standard
    45 pages
    English language
    sale 15% off
  • Standard
    49 pages
    French language
    sale 15% off

This document specifies requirements for plant-applied external three-layer polyethylene and polypropylene based coatings for corrosion protection of welded and seamless steel pipes for pipeline transportation systems in the petroleum and natural gas industries in accordance with ISO 13623. NOTE Pipes coated in accordance with this document are considered suitable for further protection by means of cathodic protection.

  • Standard
    62 pages
    English language
    sale 15% off
  • Standard
    66 pages
    French language
    sale 15% off

This document specifies the technical delivery conditions for bends made by the induction bending process for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. This document is applicable to induction bends made from seamless and welded pipe of unalloyed or low-alloy steels. NOTE These are typically C-Mn steels or low-alloy steels that are appropriate for the corresponding level and grade of line pipe in accordance with ISO 3183. This document specifies the requirements for the manufacture of two product specification levels (PSLs) of induction bends corresponding to product specification levels given for pipe in ISO 3183. This document is not applicable to the selection of the induction bend PSL. It is the responsibility of the purchaser to specify the PSL, based upon the intended use and design requirements; see also ISO 3183, Introduction. This document is not applicable to pipeline bends made by other manufacturing processes.

  • Standard
    32 pages
    English language
    sale 15% off

ISO 13623:2017 specifies requirements and gives recommendations for the design, materials, construction, testing, operation, maintenance and abandonment of pipeline systems used for transportation in the petroleum and natural gas industries. It applies to pipeline systems on-land and offshore, connecting wells, production plants, process plants, refineries and storage facilities, including any section of a pipeline constructed within the boundaries of such facilities for the purpose of its connection. The extent of pipeline systems covered by ISO 13623:2017 is illustrated in Figure 1. ISO 13623:2017 applies to rigid, metallic pipelines. It is not applicable for flexible pipelines or those constructed from other materials, such as glass-reinforced plastics. ISO 13623:2017 is applicable to all new pipeline systems and can be applied to modifications made to existing ones. It is not intended that it applies retroactively to existing pipeline systems. It describes the functional requirements of pipeline systems and provides a basis for their safe design, construction, testing, operation, maintenance and abandonment.

  • Standard
    84 pages
    English language
    sale 15% off
  • Standard
    90 pages
    French language
    sale 15% off

ISO 21809-5:2017 specifies the requirements for qualification, application, testing and handling of materials required for the application of reinforced concrete coating externally to either bare pipe or pre-coated pipe for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. The external application of concrete is primarily used for the negative buoyancy of pipes used in buried or submerged pipeline systems and/or for the mechanical protection of the pipe and its pre-coating. ISO 21809-5:2017 is applicable to concrete thicknesses of 25 mm or greater.

  • Standard
    28 pages
    English language
    sale 15% off
  • Standard
    29 pages
    French language
    sale 15% off

ISO 16440:2016 specifies requirements, including corrosion protection, for the design, fabrication, installation and maintenance of steel-cased pipelines for pipeline transportation systems in the petroleum and natural gas industries in accordance with ISO 13623. NOTE 1 Steel casings can be used for mechanical protection of pipelines at crossings, such as at roads and railways and the installation of a casing at a highway, railway, or other crossing can be required by the permitting agency or pipeline operator. NOTE 2 This document does not imply that utilization of casings is mandatory or necessary. NOTE 3 This document does not imply that cased crossings, whether electrically isolated or electrically shorted, contribute to corrosion of a carrier pipe within a cased crossing. However, cased crossings can adversely affect the integrity of the carrier pipe by shielding cathodic protection (CP) current to the carrier pipe or reducing the CP effectiveness on the carrier pipe in the vicinity of the casing. Their use is not recommended unless required by load considerations, unstable soil conditions, or when their use is dictated by sound engineering practices.

  • Standard
    39 pages
    English language
    sale 15% off
  • Standard
    39 pages
    English language
    sale 15% off
  • Standard
    42 pages
    French language
    sale 15% off

ISO 21809-3:2016 specifies requirements for field joint coating of seamless or welded steel pipes for buried and submerged sections of pipeline transportation systems used in the petroleum, petrochemical and natural gas industries as defined in ISO 13623. This part of ISO 21809 specifies the qualification, application and testing of the corrosion protection coatings applied to steel surfaces left bare after the joining of pipes and fittings (components) by welding. ISO 21809-3:2016 defines and codifies in Table 1 the different types of field joint coatings for pipelines. ISO 21809-3:2016 does not address requirements for additional mechanical protection, for thermal insulation or for joint infills of concrete weight-coated pipes. NOTE Field joints of pipes and fittings coated in accordance with this part of ISO 21809 are considered suitable for further protection by means of cathodic protection.

  • Standard
    122 pages
    English language
    sale 15% off
  • Standard
    122 pages
    English language
    sale 15% off
  • Standard
    125 pages
    French language
    sale 15% off

ISO 15589-1:2015 specifies requirements and gives recommendations for the pre-installation surveys, design, materials, equipment, installation, commissioning, operation, inspection, and maintenance of cathodic protection systems for on-land pipelines, as defined in ISO 13623 or EN 14161 for the petroleum, petrochemical, and natural gas industries, and in EN 1594 or EN 12007‑1 and EN 12007‑3 used by gas supply industries in Europe. All contents of this part of ISO 15589 are applicable to on-land pipelines and piping systems used in other industries and transporting other media such as industrial gases, waters, or slurries. ISO 15589-1:2015 applies to buried pipelines, landfalls of offshore pipeline sections protected by on-shore based cathodic protection installations, and to immersed sections of on-land pipelines such as river or lake crossings. ISO 15589-1:2015 specifies requirements for pipelines of carbon steel, stainless steel, cast iron, galvanized steel, or copper. If other pipeline materials are used, the criteria to apply are defined under the responsibility of the pipeline operator. ISO 15589-1:2015 does not apply to pipelines made of reinforced concrete for which EN 12696 can be applied. NOTE Special conditions sometimes exist where cathodic protection is ineffective or only partially effective. Such conditions can include shielding (e.g. disbonded coatings, thermal-insulating coatings, rocky soil, etc.) and unusual contaminants in the electrolyte.

  • Standard
    80 pages
    English language
    sale 15% off
  • Standard
    87 pages
    French language
    sale 15% off
  • Standard
    80 pages
    French language
    sale 15% off

ISO 12736:2014 defines the minimum requirements for qualification, application, testing, handling, storage and transportation of new and existing wet thermal insulation systems for pipelines, flowlines, equipment and subsea structures in the petroleum and natural gas industries. The purpose of these systems is to provide external corrosion protection and thermal insulation. ISO 12736:2014 is applicable to wet thermal insulation systems submerged in seawater. ISO 12736:2014 is not applicable to thermal insulation in the annulus of a steel pipe-in-pipe system.

  • Standard
    74 pages
    English language
    sale 15% off
  • Standard
    88 pages
    French language
    sale 15% off

ISO 21809-2:2014 specifies the requirements for qualification, application, testing and handling of materials for plant application of single layer fusion-bonded epoxy (FBE) coatings applied externally for the corrosion protection of bare steel pipe for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623.

  • Standard
    50 pages
    English language
    sale 15% off
  • Standard
    50 pages
    English language
    sale 15% off
  • Standard
    50 pages
    French language
    sale 15% off
  • Standard
    50 pages
    French language
    sale 15% off

ISO 13847:2013 specifies requirements, for the petroleum, petrochemical and natural gas industries, for producing and inspecting girth, branch and fillet welds in the pipeline part of pipeline transportation systems which meet the requirements of ISO 13623:2009 or equivalent. ISO 13847:2013 is applicable to the requirements for welding of carbon and low-alloy steel pipes, and includes guidance for the welding of corrosion-resistant alloy (CRA) and CRA-clad pipelines in Annex A. Application is restricted to pipes with a diameter of 20 mm or more and a wall thickness of 3 mm or more, a specified minimum yield strength of 555 MPa or less, and which are designed not to exceed permissible equivalent stresses as defined in ISO 13623:2009 or equivalent. It is also applicable to welding into pipelines of items such as spools, risers, launchers/receivers, fittings, flanges and pup pieces to pipeline valves. Guidance for special welding applications is provided in: Annex B for hyperbaric welding; Annex C for brazing and aluminothermic welding of anode leads; Annex D for branch and fillet welding on in-service pipelines. The welding processes covered are shielded metal arc welding (SMAW), gas tungsten arc welding (GTAW), gas metal arc welding (GMAW), gas-shielded flux-cored arc welding (GSFCAW), self-shielded flux-cored arc welding (SSFCAW) and submerged arc welding (SAW). ISO 13847:2013 is not applicable to flash girth welding, resistance welding, solid-phase welding or other one-shot welding processes, nor to longitudinal welds in pipe or fittings or to the welding of process piping outside the scope of ISO 13623:2009.

  • Standard
    81 pages
    English language
    sale 15% off

ISO 15589-2:2012 specifies requirements and gives recommendations for the pre-installation surveys, design, materials, equipment, fabrication, installation, commissioning, operation, inspection and maintenance of cathodic protection systems for offshore pipelines for the petroleum, petrochemical and natural gas industries as defined in ISO 13623. It is applicable to carbon steel, stainless steel and flexible pipelines in offshore service as well as to retrofits, modifications and repairs made to existing pipeline systems. ISO 15589-2:2012 is applicable to all types of seawater and seabed environments encountered in submerged conditions and on risers up to mean water level.

  • Standard
    59 pages
    English language
    sale 15% off
  • Standard
    64 pages
    French language
    sale 15% off

ISO 12490:2011 defines the requirements for mechanical integrity and sizing of actuators used on valves manufactured under ISO 14313 and API Specification 6D. ISO 12490:2011 is applicable to all types of electric, pneumatic and hydraulic actuators, inclusive of mounting kit, installed on pipeline valves. ISO 12490:2011 is not applicable to actuators installed on control valves, valves being used for regulation, valves in sub-sea service, handheld powered devices, stand-alone manually operated gearboxes, instrument tubing and associated fittings and actuator control equipment.

  • Standard
    51 pages
    English language
    sale 15% off
  • Standard
    55 pages
    French language
    sale 15% off

ISO/TS 12747:2011 gives guidance to follow, as a minimum, in order to assess the feasibility of extending the service life of a pipeline system, as defined in ISO 13623, beyond its specified design life. ISO/TS 12747:2011 applies to rigid metallic pipelines. Pump stations, compressor stations, pressure-reduction stations and depots are not specifically addressed in ISO/TS 12747:2011. ISO/TS 12747:2011 is not applicable to the following: flexible pipelines; pipelines constructed from other materials, such as glass reinforced plastics; umbilicals; topsides equipment; and structures and structural components. ISO/TS 12747:2011 is limited to life extension, which is an example of a change to the original design. Other changes, such as MAOP up-ratings, are excluded. The assessment methodology is applicable to other changes to the design at the discretion of the user.

  • Technical specification
    22 pages
    English language
    sale 15% off

ISO 21809-4:2009 specifies the requirements for qualification, application, inspection, testing, handling and storage of materials for plant application of two-layer polyethylene coatings (2-layer PE) applied externally for the corrosion protection of bare steel pipe for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623.

  • Standard
    34 pages
    English language
    sale 15% off

ISO 14723:2009 specifies requirements and gives recommendations for the design, manufacturing, testing and documentation of ball, check, gate and plug valves for subsea application in offshore pipeline systems meeting the requirements of ISO 13623 for the petroleum and natural gas industries. ISO 14723:2009 is not applicable to valves for pressure ratings exceeding PN 420 (Class 2500).

  • Standard
    72 pages
    English language
    sale 15% off
  • Standard
    72 pages
    French language
    sale 15% off

ISO 14313:2007 specifies requirements and provides recommendations for the design, manufacturing, testing and documentation of ball, check, gate and plug valves for application in pipeline systems meeting the requirements of ISO 13623 for the petroleum and natural gas industries. ISO 14313:2007 is not applicable to subsea pipeline valves, as they are covered by a separate International Standard (ISO 14723). ISO 14313:2007 is not applicable to valves for pressure ratings exceeding PN 420 (Class 2 500).

  • Standard
    77 pages
    English language
    sale 15% off

ISO 16708:2006 specifies the functional requirements and principles for design, operation and re-qualification of pipelines in the petroleum and natural gas industries using reliability based limit state methods as permitted by ISO 13623. Reliability-based limit state methods provide a systematic way to predict pipeline safety in design and operation. ISO 16708:2006 supplements ISO 13623 and can be used in cases where ISO 13623 does not provide specific guidance and where limit states methods can be applied, such as, but not limited to - qualification of new concepts, e.g. when new technology is applied or for design scenarios where industry experience is limited, - re-qualification of the pipeline due to a changed design basis, such as service-life extension, which can include reduced uncertainties due to improved integrity monitoring and operational experience, - collapse under external pressure in deep water, - extreme loads, such as seismic loads (e.g. at a fault crossing), ice loads (e.g. by impact from ice keels), - situations where strain-based criteria can be appropriate. ISO 16708:2006 applies to rigid metallic pipelines on-land and offshore used in the petroleum and natural gas industries.

  • Standard
    57 pages
    English language
    sale 15% off

ISO 21329:2004 specifies requirements and provides guidance for the testing of mechanical connectors for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. The tests specified in ISO 21329:2004 are intended to form part of the design verification process for connectors. They provide objective evidence that connectors conform to a defined performance envelope. ISO 21329:2004 does not cover the use of design procedures as part of the qualification process for mechanical connectors, nor does it address fabrication and quality control. However, it can be used as input to a qualification procedure.Although its principles can be applied, ISO 21329:2004 does not address a) connectors that are designed to rotate in use, b) manifolds, c) topsides pipework or piping, d) flanges, e) connectors used in pipelines installed by reeling or J-tube pulls, f) factory acceptance testing, g) statistical bases for risk analysis.

  • Standard
    81 pages
    English language
    sale 15% off
  • Standard
    85 pages
    French language
    sale 15% off
  • Standard
    16 pages
    English language
    sale 15% off
  • Standard
    18 pages
    French language
    sale 15% off

ISO 3183:2012 specifies requirements for the manufacture of two product specification levels (PSL 1 and PSL 2) of seamless and welded steel pipes for use in pipeline transportation systems in the petroleum and natural gas industries. ISO 3183:2012 is not applicable to cast pipe.

  • Standard
    179 pages
    English language
    sale 15% off
  • Standard
    200 pages
    French language
    sale 15% off

ISO 21809-1:2011 specifies requirements of plant-applied external three-layer polyethylene- and polypropylene-based coatings for corrosion protection of welded and seamless steel pipes for pipeline transportation systems in the petroleum and natural gas industries in accordance with ISO 13623. Pipes coated in accordance with ISO 21809-1:2011 are considered suitable for further protection by means of cathodic protection.

  • Standard
    54 pages
    English language
    sale 15% off
  • Standard
    60 pages
    French language
    sale 15% off

ISO 21809-5:2010 specifies the requirements for qualification, application, testing and handling of materials required for the application of reinforced concrete coating externally to either bare pipe or pre-coated pipe for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. ISO 21809-5:2010 is applicable to concrete thicknesses of 25 mm or greater.

  • Standard
    29 pages
    English language
    sale 15% off
  • Standard
    30 pages
    French language
    sale 15% off

ISO 15590-1:2009 specifies the technical delivery conditions for bends made by the induction bending process for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. ISO 15590-1:2009 is applicable to induction bends made from seamless and welded pipe of unalloyed or low-alloy steels. These are typically C-Mn steels or low-alloy steels that are appropriate for the corresponding level and grade of line pipe in accordance with ISO 3183. ISO 15590-1:2009 specifies the requirements for the manufacture of two product specification levels (PSL's) of induction bend corresponding to product specification levels given for pipe in ISO 3183. ISO 15590-1:2009 is not applicable to the selection of the induction bend product specification level. It is the responsibility of the purchaser to specify the PSL, based upon the intended use and design requirements; see also ISO 3183:2007, Introduction. ISO 15590-1:2009 is not applicable to pipeline bends made by other manufacturing processes.

  • Standard
    32 pages
    English language
    sale 15% off

ISO 13623:2009 specifies requirements and gives recommendations for the design, materials, construction, testing, operation, maintenance and abandonment of pipeline systems used for transportation in the petroleum and natural gas industries. ISO 13623:2009 applies to pipeline systems on land and offshore, connecting wells, production plants, process plants, refineries and storage facilities, including any section of a pipeline constructed within the boundaries of such facilities for the purpose of its connection. A figure shows the extent of pipeline systems covered by ISO 13623:2009. ISO 13623:2009 applies to rigid, metallic pipelines. It is not applicable for flexible pipelines or those constructed from other materials, such as glass-reinforced plastics. ISO 13623:2009 is applicable to all new pipeline systems and can be applied to modifications made to existing ones. It is not intended that it apply retroactively to existing pipeline systems. ISO 13623:2009 describes the functional requirements of pipeline systems and provides a basis for their safe design, construction, testing, operation, maintenance and abandonment.

  • Standard
    84 pages
    English language
    sale 15% off

ISO 21809-3:2008 specifies requirements for field joint coating of seamless or welded steel pipes for pipeline transportation systems in the petroleum and natural gas industries as defined in ISO 13623. ISO 21809-3:2008 specifies the qualification, application and testing of the corrosion protection coatings applied to steel surfaces left bare after the pipes and fittings (components) are joined by welding. ISO 21809-3:2008 does not address additional mechanical protection, thermal insulation or joint infills for concrete weight-coated pipes. ISO 21809-3:2008 defines and codifies the different types of field joint coatings for buried or submerged pipelines as presented in Table 1.

  • Standard
    99 pages
    English language
    sale 15% off

ISO 21809-2:2007 specifies the requirements for qualification, application, testing and handling of materials for plant application of single-layer fusion-bonded epoxy (FBE) coatings applied externally for the corrosion protection of bare steel pipe for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. High-temperature coatings with a glass transition of above 120 °C or FBE primer coatings for three- or multi-layer polyethylene or polypropylene coatings are not covered by ISO 21809-2:2007. Pipes coated in accordance with ISO 21809-2:2007 are considered suitable for additional protection by means of cathodic protection.

  • Standard
    37 pages
    English language
    sale 15% off
  • Standard
    40 pages
    French language
    sale 15% off

ISO 3183:2007 specifies requirements for the manufacture of two product specification levels (PSL 1 and PSL 2) of seamless and welded steel pipes for use in pipeline transportation systems in the petroleum and natural gas industries. ISO 3183:2007 is not applicable to cast pipe.

  • Standard
    143 pages
    English language
    sale 15% off

ISO 15590-3:2004 applies to weldneck and blind flanges (full face, raised face, and RTJ groove) as well as anchor, swivel-ring flanges and orifice flanges. ISO 15590-3:2004 specifies the technical requirements for carbon steel and low-alloy steel forged flanges for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. ISO 15590-3:2004 designates those categories of flanges that meet the industry's need to match ISO 3183 pipe. These flanges are for normal and low-temperature service and include supplementary requirements where required for sour service. Materials for, or the attachment of, factory-welded extensions, bolting materials, gaskets, slip-on flanges or flanged fittings are not covered by ISO 15590-3:2004. ISO 15590-3:2004 is not applicable to integrally cast or forged flanges for valves, pumps or other equipment. ISO 15590-3:2004 does not cover the selection of the flange category or pressure class. Sizes and pressure classes listed in ISO 7005-1 and applicable to ISO 15590-3:2004 are as follows: DN 10 (NPS 1/2) to DN 1500 (NPS 60); PN 20 (class 150), PN 50 (class 300), PN 100 (class 600), PN 150 (class 900), PN 250 (class 1500), PN 420 (class 2500).

  • Standard
    17 pages
    English language
    sale 15% off

ISO 15589-2:2004 specifies requirements and gives recommendations for the pre-installation surveys, design, materials, equipment, fabrication, installation, commissioning, operation, inspection and maintenance of cathodic protection systems for offshore pipelines for the petroleum and natural gas industries as defined in ISO 13623. ISO 15589-2:2004 is applicable to carbon and stainless steel pipelines in offshore service. ISO 15589-2:2004 is applicable to retrofits, modifications and repairs made to existing pipeline systems. ISO 15589-2:2004 is applicable to all types of seawater and seabed environments encountered in submerged conditions and on risers up to mean water level. Note that special conditions sometimes exist where cathodic protection is ineffective or only partially effective. Such conditions can include elevated temperatures, disbonded coatings, thermal insulating coatings, shielding, bacterial attack, and unusual contaminants in the electrolyte.

  • Standard
    54 pages
    English language
    sale 15% off

ISO 15590-2:2003 specifies the technical delivery conditions for unalloyed or low-alloy steel seamless and welded pipeline fittings for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. ISO 15590-2:2003 is applicable to welding end-fittings such as elbows, caps, tees, single or multiple extruded headers, reducers, and transition sections made from seamless and welded pipe of unalloyed or low-alloy steels. ISO 15590-2:2003 specifies three classes of fitting corresponding to increasing quality requirements in accordance with the technical delivery conditions of ISO 3183 for pipe. ISO 15590-2:2003 is not applicable to the selection of the fitting class. ISO 15590-2:2003 is not applicable to the materials for, or the attachment of, factory-welded extensions.

  • Standard
    26 pages
    English language
    sale 15% off

ISO 15589-1:2003 specifies requirements and gives recommendations for the pre-installation surveys, design, materials, equipment, fabrication, installation, commissioning, operation, inspection and maintenance of cathodic protection systems for on-land pipelines, as defined in ISO 13623, for the petroleum and natural gas industries. ISO 15589-1:2003 is applicable to buried carbon steel and stainless steel pipelines on land. It can also apply to landfalls of offshore pipeline sections protected by onshore-based cathodic protection installations. ISO 15589-1:2003 is also applicable to retrofits, modifications and repairs made to existing pipeline systems. NOTE Special conditions sometimes exist where cathodic protection is ineffective or only partially effective. Such conditions can include elevated temperatures, disbonded coatings, thermal insulating coatings, shielding, bacterial attack and unusual contaminants in the electrolyte.

  • Standard
    40 pages
    English language
    sale 15% off

La présente Norme Internationale spécifie des exigences minimales et donne des recommandations pour la conception, la fabrication, les essais et la documentation des vannes à tournant sphérique, clapets de retenue et robinets-vannes prévus pour des applications immergées dans les systèmes de conduites sous-marines satisfaisant aux exigences de l'ISO 13623 applicable aux Industries du Pétrole et du Gaz Naturel. Les vannes pour des classes de pression excédant PN 420 (classe 2500) ne sont pas couvertes par la présente Norme Internationale. L'Annexe A de la présente Norme Internationale présente des lignes directrices pour aider les acheteurs à sélectionner le type de vanne et à spécifier les exigences particulières lors d'une commande de vannes. L'Annexe B de la présente Norme Internationale présente une liste résumée des informations que le fabricant et/ou l'acheteur doivent fournir lors d'une commande de vannes.

  • Standard
    62 pages
    English language
    sale 15% off
  • Standard
    86 pages
    English language
    sale 15% off
  • Standard
    90 pages
    French language
    sale 15% off