Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for manholes and inspection chambers

This document specifies the definitions and requirements for unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) manholes and inspection chambers intended for non-pressure underground drainage and sewerage systems to a maximum depth of 6 m from ground level to the invert of the manhole or inspection chamber.
This document covers manholes and inspection chambers with flow profile bases, and their joints to the piping system.
Manholes and inspection chambers are intended to be used in pedestrian or vehicular traffic areas outside the building structure.
NOTE 1   The intended use in underground installation outside the building structure is reflected in the marking of products by the application area code "U".
NOTE 2   Products complying with this document may also be used in non-traffic areas.
NOTE 3   Products complying with this standard can be installed in underground applications without additional static calculation.
NOTE 4   Shallow chambers are specified in EN 13598-1.
Manholes and inspection chambers complying with EN 13598-2 are made from a prescribed set of components that are manufactured from unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE) and assembled together.
NOTE 5   The complete manhole or inspection chamber assembly may also include non-plastic items (near surface or surface components for example) which are not covered by this document.
NOTE 6   Manholes and inspection chambers may be supplied with covers, frame covers and gratings complying with the relevant part of EN 124 [1].
Manholes and inspection chambers complying with EN 13598-2 comply with the general requirements given in EN 476.
Manholes and inspection chambers complying with EN 13598-2 may be used for storm-water systems.
Manhole and inspection chamber components can be manufactured by various methods e.g. extrusion, injection moulding, rotational moulding, low-pressure moulding or fabricated.
NOTE 7   Manholes and inspection chambers can be site assembled from different components, but can also be manufactured as a single unit.

Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Weichmacherfreies Polyvinylchlorid (PVC-U), Polypropylen (PP) und Polyethylen (PE) - Teil 2: Anforderungen an Einsteigschächte und Kontrollschächte

Dieses Dokument legt die Begriffe und Anforderungen für Einsteigschächte und Kontrollschächte aus weichmacherfreiem Polyvinylchlorid (PVC U), Polypropylen (PP) und Polyethylen (PE) fest, die in erdverlegte drucklose Entwässerungs- und Abwassersysteme bis zu einer Maximaltiefe von 6 m ab Geländeoberkante bis zur Sohle des Einsteigschachts oder Kontrollschachts eingebaut werden.
Dieses Dokument behandelt Einsteigschächte und Kontrollschächte mit Schachtunterteilen mit Gerinneausbildung und ihre Verbindungen zum Rohrleitungssystem.
Einsteigschächte und Kontrollschächte sind für die Verwendung in Bereichen mit Fußgänger- und Fahrzeugverkehr außerhalb der Gebäudestruktur vorgesehen.
ANMERKUNG 1   Die vorgesehene Verwendung in Erdverlegung außerhalb der Gebäudestruktur wird durch die Kennzeichnung der Produkte mit dem Anwendungskennzeichen "U" wiedergegeben.
ANMERKUNG 2   Produkte, die dem vorliegenden Dokument entsprechen, dürfen auch in Bereichen ohne Verkehr verlegt werden.
ANMERKUNG 3   Produkte, die der vorliegenden Norm entsprechen, können ohne zusätzliche statische Berechnung in erdverlegte Anwendungen eingebaut werden.
ANMERKUNG 4   Schächte mit geringer Einbautiefe werden in EN 13598-1 festgelegt.
Einsteigschächte und Kontrollschächte, die EN 13598-2 erfüllen, sind aus einem vorgeschriebenen Set von Bauteilen hergestellt, die aus weichmacherfreiem Polyvinylchlorid PVC U), Polypropylen (PP), Polypropylen mit mineralischen Additiven (PP MD) oder Polyethylen (PE) bestehen und zusammengebaut sind.
ANMERKUNG 5   Die komplette Bauteilkombination des Einsteigschachts oder Kontrollschachts kann auch Elemente enthalten, die nicht aus Kunststoff sind (oberflächennahe oder Oberflächenbauteile zum Beispiel) und von dieser Norm nicht abgedeckt werden.
ANMERKUNG 6   Einsteigschächte und Kontrollschächte können mit Abdeckungen, Rahmenabdeckungen und Gittern geliefert werden, die den entsprechenden Teil von EN 124 [1] erfüllen.
Einsteigschächte und Kontrollschächte, die EN 13598-2 entsprechen, erfüllen die in EN 476 gegebenen allgemeinen Anforderungen.
Einsteigschächte und Kontrollschächte, die EN 13598-2 erfüllen, dürfen für Regenwassersysteme verwendet werden.
Einsteigschacht  und Kontrollschacht-Bauteile können in verschiedenen Verfahren hergestellt werden, z. B. Strangpressen, Spritzgießen, Rotationsgießen, Niederdruckgießen oder handgefertigt sein.
ANMERKUNG 7   Einsteig- und Kontrollschächte können vor Ort aus verschiedenen Bauteilen montiert oder als einzelne Einheit gefertigt werden.

Systèmes de canalisations en plastique pour les branchements et les collecteurs d’assainissement enterrés sans pression - Poly(chlorure de vinyle) non plastifié (PVC-U), polypropylène (PP) et polyéthylène (PE) - Partie 2 : Spécifications relatives aux regards et aux boîtes d’inspection et de branchement

Le présent document spécifie les définitions et les exigences relatives aux regards et boîtes d’inspection et de branchement en poly(chlorure de vinyle) non plastifié (PVC-U), en polypropylène (PP) et en polyéthylène (PE), destinés aux systèmes de branchements et de collecteurs d’assainissement sans pression enterrés jusqu’à une profondeur maximale de 6 m du niveau du sol au niveau du fil d’eau du regard ou de la boîte d’inspection et de branchement.
Le présent document traite des regards et des boîtes d’inspection et de branchement avec des éléments de fond à profil d’écoulement, et de leurs assemblages au système de canalisation.
Les regards et les boîtes d’inspection et de branchement sont destinés à être utilisés dans les zones de circulation de piétons ou de véhicules à l’extérieur de la structure du bâtiment.
NOTE 1   L’usage prévu dans des installations enterrées à l’extérieur de la structure du bâtiment est repéré au niveau du marquage des produits par le code de zone d’application « U ».
NOTE 2   Les produits conformes au présent document peuvent également être utilisés dans des zones sans circulation.
NOTE 3   Les produits conformes à la présente norme peuvent être mis en oeuvre dans des applications enterrées sans calculs statiques supplémentaires.
NOTE 4   Les boîtes peu profondes sont spécifiées dans l’EN 13598-1.
Les regards et les boîtes d’inspection et de branchement conformes à l’EN 13598-2 sont constitués d’un ensemble de composants prescrits qui sont fabriqués en poly(chlorure de vinyle) non plastifié (PVC-U), en polypropylène (PP), en polypropylène avec modificateurs minéraux (PP-MD) ou en polyéthylène (PE) et assemblés.
NOTE 5   Le montage complet du regard ou de la boîte d’inspection et de branchement peut également inclure des éléments non plastiques (composants supérieurs ou de surface par exemple) non couverts par le présent document.
NOTE 6   Les regards et les boîtes d’inspection et de branchement peuvent être fournis avec des tampons, des tampons avec cadre et des grilles conformes à la partie applicable de l’EN 124 [1].
Les regards et les boîtes d’inspection et de branchement conformes à l’EN 13598-2 sont conformes aux exigences générales données dans l’EN 476.
Les regards et les boîtes d’inspection et de branchement conformes à l’EN 13598-2 peuvent être utilisés pour des systèmes d’eaux pluviales.
Les composants du regard et de la boîte d’inspection et de branchement peuvent être fabriqués selon diverses méthodes, par exemple : par extrusion, par moulage par injection, moulage par rotation, moulage à basse pression ou être façonnés.
NOTE 7   Les regards et les boîtes d’inspection et de branchement peuvent être assemblés sur site à partir de différents éléments, mais ils peuvent également être fabriqués en un seul élément.

Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Nemehčan polivinilklorid (PVC-U), polipropilen (PP) in polietilen (PE) - 2. del: Specifikacije za vstopne in revizijske jaške

General Information

Status
Published
Public Enquiry End Date
19-Feb-2019
Publication Date
17-May-2020
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
12-May-2020
Due Date
17-Jul-2020
Completion Date
18-May-2020

Relations

Buy Standard

Standard
EN 13598-2:2020
English language
33 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 13598-2:2019
English language
31 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 13598-2:2020
01-junij-2020
Nadomešča:
SIST EN 13598-2:2016
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo
po težnostnem principu in so položeni v zemljo - Nemehčan polivinilklorid (PVC-
U), polipropilen (PP) in polietilen (PE) - 2. del: Specifikacije za vstopne in revizijske
jaške
Plastics piping systems for non-pressure underground drainage and sewerage -
Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) -
Part 2: Specifications for manholes and inspection chambers
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -
leitungen - Weichmacherfreies Polyvinylchlorid (PVC-U), Polypropylen (PP) und
Polyethylen (PE) - Teil 2: Anforderungen an Einsteigschächte und Kontrollschächte
Systèmes de canalisations en plastique pour les branchements et les collecteurs
d’assainissement enterrés sans pression - Poly(chlorure de vinyle) non plastifié (PVC-U),
polypropylène (PP) et polyéthylène (PE) - Partie 2 : Spécifications relatives aux regards
et aux boîtes d’inspection et de branchement
Ta slovenski standard je istoveten z: EN 13598-2:2020
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST EN 13598-2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 13598-2:2020

---------------------- Page: 2 ----------------------
SIST EN 13598-2:2020


EN 13598-2
EUROPEAN STANDARD

NORME EUROPÉENNE

May 2020
EUROPÄISCHE NORM
ICS 23.040.05; 23.040.20; 93.030 Supersedes EN 13598-2:2016
English Version

Plastics piping systems for non-pressure underground
drainage and sewerage - Unplasticized poly(vinyl chloride)
(PVC-U), polypropylene (PP) and polyethylene (PE) - Part
2: Specifications for manholes and inspection chambers
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für erdverlegte
branchements et les collecteurs d'assainissement drucklose Abwasserkanäle und -leitungen -
enterrés sans pression - Poly(chlorure de vinyle) non Weichmacherfreies Polyvinylchlorid (PVC-U),
plastifié (PVC-U), polypropylène (PP) et polyéthylène Polypropylen (PP) und Polyethylen (PE) - Teil 2:
(PE) - Partie 2 : Spécifications relatives aux regards et Anforderungen an Einsteigschächte und
aux boîtes d'inspection et de branchement Kontrollschächte
This European Standard was approved by CEN on 14 March 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13598-2:2000 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 13598-2:2020
EN 13598-2:2020 (E)
Contents Page
European foreword . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 9
4 Symbols and abbreviations . 13
4.1 Symbols . 13
4.2 Abbreviations . 14
5 Material . 14
5.1 General . 14
5.2 Compound/formulation for bases . 14
5.3 Compound/formulation for riser . 15
5.4 Compound/formulation for cones . 15
5.5 Compound/formulation for telescopic adaptors . 16
5.6 Use of non-virgin materials . 16
5.7 Sealing ring retaining components . 16
6 General characteristics . 17
6.1 Appearance . 17
6.2 Colour . 17
7 Geometrical characteristics . 17
7.1 General . 17
7.2 Dimensions of manholes and inspection chambers . 17
7.2.1 Manholes . 17
7.2.2 Inspection chambers . 17
7.3 Dimensions of base connections to pipework . 17
7.4 Geometrical characteristics of steps and ladders . 18
7.4.1 General . 18
7.4.2 Steps . 18
7.4.3 Permanently fixed ladders . 19
7.4.4 Fixing provisions for ladders . 19
8 Mechanical characteristics . 19
9 Physical characteristics . 21
9.1 Injection moulded components . 21
9.2 Factory fabricated components . 21
10 Performance requirements . 21
10.1 General performance . 21
10.2 Characterization of rotationally moulded product submitted for performance
testing . 23
11 Sealing rings . 23
12 Marking and additional documentation . 23
12.1 Marking of bases . 23
12.2 Minimum marking of components other than bases . 24
12.3 Additional documentation . 25
2

---------------------- Page: 4 ----------------------
SIST EN 13598-2:2020
EN 13598-2:2020 (E)
Annex A (normative) Test method for durability . 26
A.1 General . 26
A.2 Test procedure . 26
A.3 Material characteristics . 26
Annex B (normative) Test method for structural integrity of bases . 28
B.1 Procedure . 28
B.2 Calculation of 50-year deflection. 28
Annex C (normative) Test method for impact resistance of bases . 29
C.1 Test equipment . 29
C.2 Test procedure . 29
Annex D (normative) Utilization of non-virgin materials . 30
Bibliography . 33

3

---------------------- Page: 5 ----------------------
SIST EN 13598-2:2020
EN 13598-2:2020 (E)
European foreword
This document (EN 13598-2:2020) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by month November 2020, and conflicting
national standards shall be withdrawn at the latest by November 2020.
Attention is drawn to the possibility that some of the elements of this document may be the
subject of patent rights. CEN shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN 13598-2:2016.
Compared to the previous version, the main changes are listed below:
1) test methods have been updated to the latest EN ISO Standards where applicable;
2) the scope has been amended to clarify the products covered in this part and avoid confusion
with the scope of part 1;
3) terms and definitions have been updated and explanatory diagrams are now included;
4) material durability test requirements have been included for riser, cone and telescopic
adaptor components. The durability test method (Annex A) has also been updated;
5) the permitted use of non-virgin materials has been clarified and a new Annex D included,
with conditions and requirements for non-virgin materials;
6) fitness for purpose testing of factory fabricated components is now included;
7) the minimum marking requirement for components other than bases has been updated.
This document is part of a System Standard for plastics piping systems of a particular material for
a specified application.
System Standards are based on the results of the work being undertaken in ISO/TC 138 “Plastics
pipes, fittings and valves for the transport of fluids”, which is a Technical Committee of the
International Organization for Standardization (ISO).
They are supported by separate standards on test methods to which references are made
throughout the System Standard.
The System Standards are consistent with general standards on functional requirements and on
recommended practice for installation.
This document does not cover sewage pump chambers, valve chambers and similar products.
Separate standard(s) for manholes, inspection chambers and road gullies for storm water
systems are currently under investigation.
4

---------------------- Page: 6 ----------------------
SIST EN 13598-2:2020
EN 13598-2:2020 (E)
EN 13598 consists of the following parts under the general title Plastics piping systems for non-
pressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U),
polypropylene (PP) and polyethylene (PE):
— Part 1: Specification for ancillary fittings and shallow chambers (under revision);
— Part 2: Specifications for manholes and inspection chambers (this document);
— Part 3: Assessment of conformity (CEN/TS under revision).
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
5

---------------------- Page: 7 ----------------------
SIST EN 13598-2:2020
EN 13598-2:2020 (E)
1 Scope
This document specifies the definitions and requirements for unplasticized poly(vinyl chloride)
(PVC-U), polypropylene (PP) and polyethylene (PE) manholes and inspection chambers intended
for non-pressure underground drainage and sewerage systems up to a maximum depth of 6 m
from ground level to the invert of the manhole or inspection chamber.
This document covers manholes and inspection chambers, with bases having a flow channel, and
their joints to the piping system.
Manholes and inspection chambers are intended to be used in pedestrian or vehicular traffic
areas outside the building structure.
NOTE 1 The intended use in underground installation outside the building structure is reflected in the
marking of products by the application area code “U”.
NOTE 2 Products complying with this document can also be used in non-traffic areas.
NOTE 3 Products complying with this standard can be installed in underground applications without
additional static calculation.
NOTE 4 Shallow chambers are specified in EN 13598-1 [1].
Manholes and inspection chambers complying with EN 13598-2 are made from a prescribed set
of components that are manufactured from unplasticized poly(vinyl chloride) (PVC-U),
polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE) and
assembled together.
NOTE 5 The complete manhole or inspection chamber assembly can also include items which are not
covered by this document (for example near surface or surface components).
NOTE 6 Manholes and inspection chambers can be supplied with covers, frame covers and gratings
complying with the relevant part of EN 124 [2].
Manholes and inspection chambers complying with EN 13598-2 may be used for storm-water
systems.
Manhole and inspection chamber components can be manufactured by various methods e.g.
extrusion, injection moulding, rotational moulding, low-pressure moulding or fabricated.
NOTE 7 Manholes and inspection chambers can be site assembled from different components, but can
also be manufactured as a single unit.
NOTE 8 Manholes and inspection chambers can be subject to national regulations and / or local
provisions.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
EN 476, General requirements for components used in drains and sewers
EN 681-1, Elastomeric seals — Materials requirements for pipe joint seals used in water and
drainage applications — Part 1: Vulcanized rubber
6

---------------------- Page: 8 ----------------------
SIST EN 13598-2:2020
EN 13598-2:2020 (E)
EN 681-2, Elastomeric Seals — Materials requirements for pipe joint seals used in water and
drainage applications — Part 2: Thermoplastic elastomers
EN 681-3, Elastomeric seals — Materials requirements for pipe joint seals used in water and
drainage applications — Part 3: Cellular materials of vulcanized rubber
EN 681-4, Elastomeric seals — Materials requirements for pipe joint seals used in water and
drainage applications — Part 4: Cast polyurethane sealing elements
EN 1401-1, Plastics piping systems for non-pressure underground drainage and sewerage —
Unplasticized poly(vinyl chloride) (PVC-U) — Part 1: Specifications for pipes, fittings and the system
EN 1852-1, Plastics piping systems for non-pressure underground drainage and sewerage —
Polypropylene (PP) — Part 1: Specifications for pipes, fittings and the system
EN 1905, Plastics piping systems — Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and
material — Method for assessment of the PVC content based on total chlorine content
EN 12099, Plastics piping systems — Polyethylene piping materials and components —
Determination of volatile content
EN 12666-1, Plastics piping systems for non-pressure underground drainage and sewerage
Polyethylene (PE) — Part 1: Specifications for pipes, fittings and the system
EN 13101:2002, Steps for underground man entry chambers — Requirements, marking, testing and
evaluation of conformity
EN 13476-2, Plastics piping systems for non-pressure underground drainage and sewerage —
Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP)
and polyethylene (PE) — Part 2: Specifications for pipes and fittings with smooth internal and
external surface and the system, Type A
EN 13476-3, Plastics piping systems for non-pressure underground drainage and sewerage —
Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP)
and polyethylene (PE) — Part 3: Specifications for pipes and fittings with smooth internal and
profiled external surface and the system, Type B
EN 14396, Fixed ladders for manholes
EN 14758-1, Plastics piping systems for non-pressure underground drainage and sewerage —
Polypropylene with mineral modifiers (PP-MD) — Part 1: Specifications for pipes, fittings and the
system
EN ISO 1043-1, Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their
special characteristics (ISO 1043-1)
EN ISO 1133-1, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow
rate (MVR) of thermoplastics — Part 1: Standard method (ISO 1133-1)
EN ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1:
Immersion method, liquid pyknometer method and titration method (ISO 1183-1)
EN ISO 1183-2, Plastics — Methods for determining the density of non-cellular plastics — Part 2:
Density gradient column method (ISO 1183-2)
7

---------------------- Page: 9 ----------------------
SIST EN 13598-2:2020
EN 13598-2:2020 (E)
EN ISO 2507-1, Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General
test method (ISO 2507-1)
EN ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions
(ISO 3126)
EN ISO 3127, Thermoplastics pipes — Determination of resistance to external blows — Round-the-
clock method (ISO 3127)
EN ISO 3451-1, Plastics — Determination of ash — Part 1: General methods (ISO 3451-1)
EN ISO 3451-5, Plastics — Determination of ash — Part 5: Poly(vinyl chloride) (ISO 3451-5)
EN ISO 9967:2016, Thermoplastics pipes — Determination of creep ratio (ISO 9967:2016)
EN ISO 11357-6, Plastics — Differential scanning calorimetry (DSC) — Part 6: Determination of
oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
(ISO 11357-6)
EN ISO 13229, Thermoplastics piping systems for non-pressure applications — Unplasticized
poly(vinyl chloride) (PVC-U) pipes and fittings — Determination of the viscosity number and K-value
(ISO 13229)
EN ISO 13254, Thermoplastics piping systems for non-pressure applications — Test method for
watertightness (ISO 13254)
EN ISO 13259, Thermoplastics piping systems for underground non-pressure applications — Test
method for leaktightness of elastomeric sealing ring type joints (ISO 13259)
EN ISO 13263, Thermoplastics piping systems for non-pressure underground drainage and
sewerage — Thermoplastics fittings — Test method for impact strength (ISO 13263)
ISO 13266:2010, Thermoplastics piping systems for non-pressure underground drainage and
sewerage — Thermoplastics shafts or risers for inspection chambers and manholes —
Determination of resistance against surface and traffic loading (ISO 13266)
ISO 13267, Thermoplastics piping systems for non-pressure underground drainage and
sewerage — Thermoplastics inspection chamber and manhole bases — Test methods for buckling
resistance (ISO 13267)
ISO 13268, Thermoplastics piping systems for non-pressure underground drainage and
sewerage — Thermoplastics shafts or risers for inspection chambers and manholes —
Determination of ring stiffness
8

---------------------- Page: 10 ----------------------
SIST EN 13598-2:2020
EN 13598-2:2020 (E)
3 Terms and definitions
For the purposes of this document, the terms, definitions and abbreviations given in EN ISO 1043-
1 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp
3.1
manhole
chamber with a removable cover constructed in a drain or sewer to permit entry by personnel,
with a riser of 800 mm minimum inner diameter
Note 1 to entry: Figure 1 shows typical manholes.
Note 2 to entry: See EN 476 for dimensions of non-circular manholes.
Note 3 to entry: Manholes are subject to national safety regulations and / or local provisions regarding
man-entry limitations.
3.2
inspection chamber
chamber with a removable cover constructed in a drain or sewer that permits the introduction of
cleaning and inspection equipment from surface level, but does not provide access for personnel,
with a riser of 200 mm minimum outer diameter and an inner diameter of less than 800 mm
Note 1 to entry: Figure 2 shows typical inspection chambers.
Note 2 to entry: See EN 476 for non-circular chambers.
3.3
base
bottom part of a manhole or inspection chamber, allowing direct connection to buried drain or
sewer pipes and including integrally formed channels with benching as appropriate
Note 1 to entry: In case of a one-piece manhole or inspection chamber, for testing purposes the base
component ends at a distance of minimum 300 mm measured from the top of the main channel. Above
300 mm the section should be considered as a riser and tested accordingly.
Note 2 to entry: Bases having a spherical design may be used. National regulations can apply.
3.4
flow channel
open and accessible continuation of the sewer network in a manhole or inspection chamber to
allow directional changes maintaining the hydraulic performance of a sewer system
Note 1 to entry: The term flow profile is also used.
3.5
benching
sloped surface adjacent to the channel in a manhole or inspection chamber
9

---------------------- Page: 11 ----------------------
SIST EN 13598-2:2020
EN 13598-2:2020 (E)
3.6
riser
component which is connected onto a base and which defines the nominal size of the manhole or
inspection chamber
Note 1 to entry: The riser can be supplied either as one or more separate items, for site jointing to the
base, or integrated with the base.
Note 2 to entry: In case of a one-piece manhole or inspection chamber, for testing purposes the riser
component starts at a distance of minimum 300 mm measured from the top of the main channel. Below
300 mm the section should be considered as a base and tested accordingly.
3.7
telescopic adaptor
part of the assembly on top of the riser or cone that allows adjustment of the surface component
or near surface component
Note 1 to entry: Telescopic adaptors allow accommodation of settlement during lifetime and eliminate
the transmission of vehicular loading down the riser.
3.8
cone
adapter allowing change in diameter, close to ground level
3.9
near-surface component
component intended to spread vehicular loading directly to the soil and/or provide a seating for
the cover and its frame
3.10
assembly
items collectively forming a manhole or inspection chamber
Note 1 to entry: See typical examples in Figures 1 and 2.
3.11
invert
lowest point of the internal surface of the barrel of a pipe or channel at any cross section
3.12
maximum height of groundwater above invert
H
w
height of water column above the invert that the manhole or inspection chamber can withstand
during use
3.13
virgin material
material in a form such as granules or powder that has not been subjected to use or processing
other than that required for its manufacture and to which no reprocessed or recycled material
has been added
10

---------------------- Page: 12 ----------------------
SIST EN 13598-2:2020
EN 13598-2:2020 (E)
3.14
own reprocessed material
material prepared from unused products, including trimmings from the production, that will be
reprocessed in a manufacturer’s plant after having been previously processed by the same
manufacturer
3.15
recycled material
material prepared from used thermoplastic products which have been cleaned and crushed or
ground
3.16
agreed specification
specification of the relevant material characteristics agreed between the supplier of the non-
virgin material and the manufacturer
11

---------------------- Page: 13 ----------------------
SIST EN 13598-2:2020
EN 13598-2:2020 (E)

Key
a cover (not covered by this document) 1 inlet
b near surface component (not covered by this 2 outlet
document)
c telescopic adaptor 3 invert
d cone 4 inner diameter
e riser 5 benching
1
e considered as riser 6 channel
2
f base
1
f considered as base
2
g connection
Figure 1 — Typical manholes
12

---------------------- Page: 14 ----------------------
SIST EN 13598-2:2020
EN 13598-2:2020 (E)

Key
a cover (not covered by this document) 1 inlet
b near surface component (not covered by this 2 outlet
document)
c telescopic adaptor 3 invert
e1 riser 4 inner diameter
e2 considered as riser 5 benching
f base 6 channel
1
f2 considered as base
g connection
Figure 2 — Typical inspection chambers
4 Symbols and abbreviations
4.1 Symbols
For the purposes of this document, the following symbols apply.
A  length of engagement
d  nominal outside diameter
n
d  mean outside diameter
em
d  mean inside diameter of socket
sm
H  maximum height of groundwater above invert
w
L  length of spigot
1
13

---------------------- Page: 15 ----------------------
SIST EN 13598-2:2020
EN 13598-2:2020 (E)
4.2 Abbreviations
For the purposes of this document, the following abbreviations apply.
MFR  melt mass-flow rate
OIT  oxidation induction time
PE  polyethylene
PP  polypropylene
PP-MD  polypropylene modified with minerals
PVC-U  unplasticized poly(vinyl chloride)
5 Material
5.1 General
Components of manholes and inspection chambers may be manufactured from different
compounds/formulations.
The compound/formulation shall be PVC-U resin, PP or PE polymer, additives and if applicable
...

SLOVENSKI STANDARD
oSIST prEN 13598-2:2019
01-februar-2019
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DRGSDGQRYRGRLQNDQDOL]DFLMRNLGHOXMHMR
SRWHåQRVWQHPSULQFLSXLQVRSRORåHQLY]HPOMR1HPHKþDQSROLYLQLONORULG 39&
8 SROLSURSLOHQ 33 LQSROLHWLOHQ 3( GHO6SHFLILNDFLMH]DYVWRSQHLQUHYL]LMVNH
MDãNH
Plastics piping systems for non-pressure underground drainage and sewerage -
Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) -
Part 2: Specifications for manholes and inspection chambers
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -
leitungen - Weichmacherfreies Polyvinylchlorid (PVC-U), Polypropylen (PP) und
Polyethylen (PE) - Teil 2: Anforderungen an Einsteigschächte und Kontrollschächte
Systèmes de canalisations en plastique pour les branchements et les collecteurs
d’assainissement enterrés sans pression - Poly(chlorure de vinyle) non plastifié (PVC-U),
polypropylène (PP) et polyéthylène (PE) - Partie 2 : Spécifications relatives aux regards
et aux boîtes d’inspection et de branchement
Ta slovenski standard je istoveten z: prEN 13598-2
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
oSIST prEN 13598-2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 13598-2:2019

---------------------- Page: 2 ----------------------
oSIST prEN 13598-2:2019


DRAFT
EUROPEAN STANDARD
prEN 13598-2
NORME EUROPÉENNE

EUROPÄISCHE NORM

December 2018
ICS 23.040.05; 23.040.20; 93.030 Will supersede EN 13598-2:2016
English Version

Plastics piping systems for non-pressure underground
drainage and sewerage - Unplasticized poly(vinyl chloride)
(PVC-U), polypropylene (PP) and polyethylene (PE) - Part
2: Specifications for manholes and inspection chambers
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für erdverlegte
branchements et les collecteurs d'assainissement drucklose Abwasserkanäle und -leitungen -
enterrés sans pression - Poly(chlorure de vinyle) non Weichmacherfreies Polyvinylchlorid (PVC-U),
plastifié (PVC-U), polypropylène (PP) et polyéthylène Polypropylen (PP) und Polyethylen (PE) - Teil 2:
(PE) - Partie 2 : Spécifications relatives aux regards et Anforderungen an Einsteigschächte und
aux boîtes d'inspection et de branchement Kontrollschächte
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 155.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13598-2:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 13598-2:2019
prEN 13598-2:2018 (E)
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 8
4 Symbols and abbreviations . 12
4.1 Symbols . 12
4.2 Abbreviations . 12
5 Material . 12
5.1 General . 12
5.2 Compound/formulation for bases . 12
5.3 Compound/formulation for riser . 13
5.4 Compound/formulation for cones . 14
5.5 Compound/formulation for telescopic adaptors . 14
5.6 Use of non-virgin materials . 15
5.7 Sealing ring retaining components . 15
6 General characteristics . 15
6.1 Appearance . 15
6.2 Colour . 15
7 Geometrical characteristics . 15
7.1 Dimensions . 15
7.1.1 General . 15
7.1.2 Base connections to pipework . 16
7.2 Geometrical characteristics of steps and ladders . 16
7.2.1 General . 16
7.2.2 Steps . 16
7.2.3 Permanently fixed ladders . 17
7.2.4 Fixing provisions for ladders . 17
8 Mechanical characteristics . 17
9 Physical characteristics of injection moulded components . 19
10 Performance requirements . 19
10.1 General performance . 19
10.2 Characterization of rotationally moulded product submitted for performance
testing . 21
11 Sealing rings . 21
12 Marking and additional documentation . 21
12.1 Marking of bases . 21
12.2 Minimum marking of components other than bases . 22
12.3 Additional documentation . 23
Annex A (normative) Durability test method . 24
A.1 General . 24
A.2 Test procedure . 24
2

---------------------- Page: 4 ----------------------
oSIST prEN 13598-2:2019
prEN 13598-2:2018 (E)
A.3 Material characteristics . 24
Annex B (normative) Structural integrity of base . 26
B.1 General . 26
B.2 Test procedure . 26
B.3 Evaluation of data . 26
Annex C (normative) Impact test on manhole or inspection chamber bases . 27
C.1 Test equipment . 27
C.2 Test procedure . 27
Annex D (normative) Utilization of non-virgin materials . 28
D.1 Utilization of non-virgin materials . 28
Bibliography . 31

3

---------------------- Page: 5 ----------------------
oSIST prEN 13598-2:2019
prEN 13598-2:2018 (E)
European foreword
This document (prEN 13598-2:2018) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13598-2:2016.
Compared to the previous version, the main changes are listed below:
1) test methods have been updated to the latest EN ISO Standards where applicable;
2) the scope has been amended to clarify the products covered in this part and avoid confusion
with the scope of part 1;
3) terms and definitions have been updated and explanatory diagrams are now included;
4) material durability test requirements have been included for riser, cone and telescopic
adaptor components. The durability test method (Annex A) has also been updated;
5) the permitted use of non-virgin materials has been clarified and a new Annex D included,
with conditions and requirements for non-virgin materials;
6) fitness for purpose testing of factory fabricated components is now included;
7) the minimum marking requirement for components other than bases has been updated.
This document is part of a System Standard for plastics piping systems of a particular material for
a specified application. There are a number of such System Standards.
System Standards are based on the results of the work being undertaken in ISO/TC 138 “Plastics
pipes, fittings and valves for the transport of fluids”, which is a Technical Committee of the
International Organization for Standardization (ISO).
They are supported by separate standards on test methods to which references are made
throughout the System Standard.
The System Standards are consistent with general standards on functional requirements and on
recommended practice for installation.
EN 13598 consists of the following parts under the general title Plastics piping systems for non-
pressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U),
polypropylene (PP) and polyethylene (PE):
— Part 1: Specification for ancillary fittings and shallow chambers (under revision);
— Part 2: Specifications for manholes and inspection chambers (this document);
— Part 3: Assessment of conformity (CEN/TS under revision).
4

---------------------- Page: 6 ----------------------
oSIST prEN 13598-2:2019
prEN 13598-2:2018 (E)
1 Scope
This document specifies the definitions and requirements for unplasticized poly(vinyl chloride)
(PVC-U), polypropylene (PP) and polyethylene (PE) manholes and inspection chambers intended
for non-pressure underground drainage and sewerage systems to a maximum depth of 6 m from
ground level to the invert of the manhole or inspection chamber.
This document covers manholes and inspection chambers with flow profile bases, and their joints
to the piping system.
Manholes and inspection chambers are intended to be used in pedestrian or vehicular traffic
areas outside the building structure.
NOTE 1 The intended use in underground installation outside the building structure is reflected in the
marking of products by the application area code “U”.
NOTE 2 Products complying with this document may also be used in non-traffic areas.
NOTE 3 Products complying with this standard can be installed in underground applications without
additional static calculation.
NOTE 4 Shallow chambers are specified in EN 13598-1.
Manholes and inspection chambers complying with EN 13598-2 are made from a prescribed set
of components that are manufactured from unplasticized poly(vinyl chloride) (PVC-U),
polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE) and
assembled together.
NOTE 5 The complete manhole or inspection chamber assembly can also include non-plastic items (near
surface or surface components for example) which are not covered by this document.
NOTE 6 Manholes and inspection chambers can be supplied with covers, frame covers and gratings
complying with the relevant part of EN 124 [1].
Manholes and inspection chambers complying with EN 13598-2 comply with the general
requirements given in EN 476.
Manholes and inspection chambers complying with EN 13598-2 may be used for storm-water
systems.
Manhole and inspection chamber components can be manufactured by various methods e.g.
extrusion, injection moulding, rotational moulding, low-pressure moulding or fabricated.
NOTE 7 Manholes and inspection chambers can be site assembled from different components, but can
also be manufactured as a single unit.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
EN 476, General requirements for components used in drains and sewers
EN 681-1, Elastomeric seals — Materials requirements for pipe joint seals used in water and
drainage applications — Part 1: Vulcanized rubber
5

---------------------- Page: 7 ----------------------
oSIST prEN 13598-2:2019
prEN 13598-2:2018 (E)
EN 681-2, Elastomeric Seals — Materials requirements for pipe joint seals used in water and
drainage applications — Part 2: Thermoplastic elastomers
EN 681-3, Elastomeric seals — Materials requirements for pipe joint seals used in water and
drainage applications — Part 3: Cellular materials of vulcanized rubber
EN 681-4, Elastomeric seals — Materials requirements for pipe joint seals used in water and
drainage applications — Part 4: Cast polyurethane sealing elements
EN 1401-1, Plastics piping systems for non-pressure underground drainage and sewerage —
Unplasticized poly(vinyl chloride) (PVC-U) — Part 1: Specifications for pipes, fittings and the system
EN 1852-1, Plastics piping systems for non-pressure underground drainage and sewerage —
Polypropylene (PP) — Part 1: Specifications for pipes, fittings and the system
EN 1905, Plastics piping systems — Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and
material — Method for assessment of the PVC content based on total chlorine content
EN 12099, Plastics piping systems — Polyethylene piping materials and components —
Determination of volatile content
EN 12666-1, Plastics piping systems for non-pressure underground drainage and sewerage
Polyethylene (PE) — Part 1: Specifications for pipes, fittings and the system
EN 13101:2002, Steps for underground man entry chambers - Requirements, marking, testing and
evaluation of conformity
EN 13476-2, Plastics piping systems for non-pressure underground drainage and sewerage —
Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP)
and polyethylene (PE) — Part 2: Specifications for pipes and fittings with smooth internal and
external surface and the system, Type A
EN 13476-3, Plastics piping systems for non-pressure underground drainage and sewerage —
Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP)
and polyethylene (PE) — Part 3: Specifications for pipes and fittings with smooth internal and
profiled external surface and the system, Type B
EN 13598-1, Plastics piping systems for non-pressure underground drainage and sewerage —
Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 1:
Specifications for ancillary fittings including shallow inspection chambers
EN 14396, Fixed ladders for manholes
EN 14758-1, Plastics piping systems for non-pressure underground drainage and sewerage —
Polypropylene with mineral modifiers (PP-MD) — Part 1: Specifications for pipes, fittings and the
system
EN 15346:2014, Plastics — Recycled plastics — Characterization of poly(vinyl chloride) (PVC)
recyclates
EN ISO 1043-1, Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their
special characteristics (ISO 1043-1)
EN ISO 1133-1:2011, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-
flow rate (MVR) of thermoplastics — Part 1: Standard method (ISO 1133-1)
6

---------------------- Page: 8 ----------------------
oSIST prEN 13598-2:2019
prEN 13598-2:2018 (E)
EN ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1:
Immersion method, liquid pyknometer method and titration method (ISO 1183-1)
EN ISO 1183-2, Plastics — Methods for determining the density of non-cellular plastics — Part 2:
Density gradient column method (ISO 1183-2)
EN ISO 2507-1, Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General
test method (ISO 2507-1)
EN ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions (ISO
3126)
EN ISO 3127, Thermoplastics pipes — Determination of resistance to external blows — Round-the-
clock method (ISO 3127)
EN ISO 3451-1, Plastics — Determination of ash — Part 1: General methods (ISO 3451-1)
EN ISO 3451-5, Plastics — Determination of ash — Part 5: Poly(vinyl chloride) (ISO 3451-5)
EN ISO 9967, Thermoplastics pipes — Determination of creep ratio (ISO 9967)
EN ISO 11357-6, Plastics — Differential scanning calorimetry (DSC) — Part 6: Determination of
oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) (ISO
11357-6)
EN ISO 13229, Thermoplastics piping systems for non-pressure applications — Unplasticized
poly(vinyl chloride) (PVC-U) pipes and fittings — Determination of the viscosity number and K-value
(ISO 13229)
EN ISO 13254, Thermoplastics piping systems for non-pressure applications — Test method for
watertightness (ISO 13254)
EN ISO 13259, Thermoplastics piping systems for underground non-pressure applications — Test
method for leaktightness of elastomeric sealing ring type joints (ISO 13259)
EN ISO 13263, Thermoplastics piping systems for non-pressure underground drainage and
sewerage - Thermoplastics fittings — Test method for impact strength (ISO 13263)
prEN ISO 13266, Thermoplastics piping systems for non-pressure underground drainage and
sewerage — Thermoplastics shafts or risers for inspection chambers and manholes —
Determination of resistance against surface and traffic loading (ISO 13266)
prEN ISO 13267, Thermoplastics piping systems for non-pressure underground drainage and
sewerage — Thermoplastics inspection chamber and manhole bases — Test methods for buckling
resistance (ISO 13267)
prEN ISO 13268, Thermoplastics piping systems for non-pressure underground drainage and
sewerage — Thermoplastics shafts or risers for inspection chambers and manholes —
Determination of ring stiffness (ISO 13268)
7

---------------------- Page: 9 ----------------------
oSIST prEN 13598-2:2019
prEN 13598-2:2018 (E)
3 Terms and definitions
For the purposes of this document, the terms, definitions and abbreviations given in
EN ISO 1043-1 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
3.1
manhole
chamber with a removable cover constructed in a drain or sewer to permit entry by personnel,
with a riser of 800 mm minimum inner diameter
Note 1 to entry: Figure 1 shows typical manholes.
Note 2 to entry: See EN 476 for dimensions of non-circular manholes.
Note 3 to entry: Manholes are subject to national safety regulations and / or local provisions regarding
man-entry limitations.
3.2
inspection chamber
chamber with a removable cover constructed in a drain or sewer that permits the introduction of
cleaning and inspection equipment from surface level, but does not provide access for personnel,
with a riser of 200 mm minimum outer diameter and an inner diameter of less than 800 mm
Note 1 to entry: Figure 2 shows typical inspection chambers.
Note 2 to entry: See EN 476 for non-circular chambers.
Note 3 to entry: Inspection chambers are subject to national safety regulations and / or local provisions.
3.3
base
bottom part of a manhole or inspection chamber, allowing direct connection to buried drain or
sewer pipes and including integrally formed channels with benching as appropriate
Note 1 to entry: In case of a one-piece manhole or inspection chamber, for testing purposes the base
component ends at a distance of 300 mm measured from the top of the main channel. Above 300 mm the
section should be considered as a riser and tested accordingly.
3.4
riser
component which is connected onto a base and which defines the nominal size of the manhole or
inspection chamber
Note 1 to entry: The riser can be supplied either as one or more separate items, for site jointing to the
base, or integrated with the base.
Note 2 to entry: In case of a one-piece manhole or inspection chamber, for testing purposes the riser
component starts at a distance of 300 mm measured from the top of the main channel. Below 300 mm the
section should be considered as a base and tested accordingly.
8

---------------------- Page: 10 ----------------------
oSIST prEN 13598-2:2019
prEN 13598-2:2018 (E)
3.5
telescopic adaptor
part of the assembly on top of the riser or cone that allows adjustment of the surface components
or near surface components
Note 1 to entry: Telescopic adaptors allows accommodation of settlement during lifetime and eliminate
the transmission of vehicular loading down the riser.
3.6
cone
adapter allowing change in diameter, close to ground level
3.7
near-surface components
components intended to spread vehicular loading directly to the soil and/or provide a seating for
the cover and its frame
3.8
assembly
items collectively forming a manhole or inspection chamber (see examples in Figures 1 and 2)
3.9
invert
lowest point of the internal surface of the barrel of a pipe or channel at any cross section
3.10
maximum height of groundwater above invert
H
w
height of water column above the invert that the manhole or inspection chamber can withstand
during use
3.11
virgin material
material in a form such as granules or powder that has not been subjected to use or processing
other than that required for its manufacture and to which no reprocessed or recycled material
has been added
Note 1 to entry: It is understood that the addition of additives such as stabilizers and pigments is still
resulting into a virgin material.
3.12
own reprocessed material
material prepared from unused products, including trimmings from the production, that will be
reprocessed in a manufacturer’s plant after having been previously processed by the same
manufacturer
3.13
recycled material
material prepared from used thermoplastic products which have been cleaned and crushed or
ground
3.14
agreed specification
specification of the relevant material characteristics agreed between the supplier of the non-
virgin material and the manufacturer
9

---------------------- Page: 11 ----------------------
oSIST prEN 13598-2:2019
prEN 13598-2:2018 (E)

Key
a cover (not part of this standard)
b near surface component
c telescopic adaptor
d cone
e riser
1
e2 considered as riser
f1 base
f considered as base
2
g connection
1 inlet
2 outlet
3 invert
4 DN/ID
Figure 1 — Typical manholes
10

---------------------- Page: 12 ----------------------
oSIST prEN 13598-2:2019
prEN 13598-2:2018 (E)

Key
a cover (not part of this standard)
b near surface component
c telescopic adaptor
e riser
1
e considered as riser
2
f1 base
f2 considered as base
g connection
1 inlet
2 outlet
3 invert
4 DN/ID
Figure 2 — Typical inspection chambers
11

---------------------- Page: 13 ----------------------
oSIST prEN 13598-2:2019
prEN 13598-2:2018 (E)
4 Symbols and abbreviations
For the purposes of this document, the following symbols and abbreviations apply.
4.1 Symbols
A  length of engagement
d  outside diameter
e
d  mean outside diameter
em
d  mean inside diameter of socket
sm
H  maximum height of groundwater above invert
w
L  length of spigot
1
4.2 Abbreviations
DN/ID  nominal size, inside diameter related
MFR  melt mass-flow rate
OIT  oxidation induction time
PE  polyethylene
PP  polypropylene
PP-MD  polypropylene modified with minerals
PVC-U  unplasticized poly(vinyl chloride)
5 Material
5.1 General
Components of manholes and inspection chambers may be manufactured from different
compounds/formulations.
The compound/formulation shall be PVC-U resin, PP or PE polymer, additives and if applicable
non-virgin material that shall allow the final component to comply with the requirements of this
document.
5.2 Compound/formulation for bases
The base shall be tested according to Table 1.
For materials complying with Table 2, the testing time may be reduced according to footnote c in
Table 1.
12

---------------------- Page: 14 ----------------------
oSIST prEN 13598-2:2019
prEN 13598-2:2018 (E)
Table 1 — Durability requirements for bases
Test parameters
Test
Characteristic Requirement
method
Parameter Value
Durability No cracks or −0,1×Hw/R bar b
Annex A
test pressure, P
crazes
2 m ≤ Hw ≤ 5 m
maximum height of

groundwater above invert, Hw
Shall conform to
a

Table A.1
rating factor, R
c
3 000 h
testing time, t
Shall conform to
test temp, T
Table A.1
a
Test in accordance with the manufacturer's declared maximum height of groundwater. The minimum value
of 2 m is based on the need to safeguard durability where there is no groundwater present, the maximum value
of 5 m is suitable for 6 m depth of installation.
b
When testing for the durability of materials rubber ring joints can be replaced by welding.
c
For materials co
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.