SIST EN 1993-1-5:2007/A2:2019
(Amendment)Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements
Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements
EN 1993-1-5 gives design requirements of stiffened and unstiffened plates which are subject to inplane forces. Effects due to shear lag, in-plane load introduction and plate buckling for I-section girders and box girders are covered. Also covered are plated structural components subject to in-plane loads as in tanks and silos. The effects of out-of-plane loading are outside the scope of this document.
Eurocode 3 - Bemessung und Konstruktion von Stahlbauten - Teil 1-5: Plattenförmige Bauteile
Eurocode 3 - Calcul des structures en acier - Partie 1-5: Plaques planes
Evrokod 3: Projektiranje jeklenih konstrukcij - 1-5. del: Elementi pločevinaste konstrukcije
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 1993-1-5:2007/A2:2019
01-oktober-2019
Evrokod 3: Projektiranje jeklenih konstrukcij - 1-5. del: Elementi pločevinaste
konstrukcije
Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements
Eurocode 3 - Bemessung und Konstruktion von Stahlbauten - Teil 1-5: Plattenförmige
Bauteile
Eurocode 3 - Calcul des structures en acier - Partie 1-5: Plaques planes
Ta slovenski standard je istoveten z: EN 1993-1-5:2006/A2:2019
ICS:
91.010.30 Tehnični vidiki Technical aspects
91.080.13 Jeklene konstrukcije Steel structures
SIST EN 1993-1-5:2007/A2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1993-1-5:2007/A2:2019
---------------------- Page: 2 ----------------------
SIST EN 1993-1-5:2007/A2:2019
EN 1993-1-5:2006/A2
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2019
EUROPÄISCHE NORM
ICS 91.010.30; 91.080.13
English Version
Eurocode 3 - Design of steel structures - Part 1-5: Plated
structural elements
Eurocode 3 - Calcul des structures en acier - Partie 1-5: Eurocode 3 - Bemessung und Konstruktion von
Plaques planes Stahlbauten - Teil 1-5: Plattenförmige Bauteile
This amendment A2 modifies the European Standard EN 1993-1-5:2006; it was approved by CEN on 11 June 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
...
SLOVENSKI STANDARD
SIST EN 1993-1-5:2007/oprA2:2019
01-april-2019
(YURNRG 3URMHNWLUDQMHMHNOHQLKNRQVWUXNFLMGHO (OHPHQWLSORþHYLQDVWH
NRQVWUXNFLMH
Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements
Eurocode 3 - Bemessung und Konstruktion von Stahlbauten - Teil 1-5: Plattenförmige
Bauteile
Eurocode 3 - Calcul des structures en acier - Partie 1-5: Plaques planes
Ta slovenski standard je istoveten z: EN 1993-1-5:2006/prA2
ICS:
91.010.30 7HKQLþQLYLGLNL Technical aspects
91.080.13 Jeklene konstrukcije Steel structures
SIST EN 1993-1-5:2007/oprA2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1993-1-5:2007/oprA2:2019
---------------------- Page: 2 ----------------------
SIST EN 1993-1-5:2007/oprA2:2019
DRAFT
EUROPEAN STANDARD
EN 1993-1-5:2006
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
February 2019
ICS 91.010.30; 91.080.13
English Version
Eurocode 3 - Design of steel structures - Part 1-5: Plated
structural elements
Eurocode 3 - Calcul des structures en acier - Partie 1-5: Eurocode 3 - Bemessung und Konstruktion von
Plaques planes Stahlbauten - Teil 1-5: Plattenförmige Bauteile
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 250.
This draft amendment A2, if approved, will modify the European Standard EN 1993-1-5:2006. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.