SIST EN ISO 24023-2:2020
(Main)Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 24023-2:2020)
Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 24023-2:2020)
This document specifies the methods of preparation of test specimens and the test methods to be used
in determining the properties of PVC-P moulding and extrusion materials. It gives the requirements for
handling test materials and for conditioning both the test material before moulding and the specimens
before testing.
This document gives procedures and conditions for the preparation of test specimens and procedures
for measuring properties of the materials from which these specimens are made. It lists properties and
test methods which are suitable and necessary to characterize PVC-P moulding and extrusion materials.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in
wide use for, or of particular significance to, these moulding and extrusion materials are also included
in this document, as are the designatory properties specified in ISO 24023 (all parts).
Kunststoffe - Weichmacherhaltige Polyvinylchlorid(PVC-P)-Werkstoffe - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 24023-2:2020)
Dieses Dokument legt die Verfahren für die Herstellung von Probekörpern und die zur Bestimmung der Eigenschaften von PVC P-Werkstoffen anzuwendenden Prüfverfahren fest. Es enthält die Anforderungen an die Handhabung der Prüfmaterialien und an die Konditionierung sowohl des Prüfmaterials vor dem Formen als auch der Probekörper vor der Prüfung.
Dieses Dokument enthält Verfahren und Bedingungen für die Herstellung von Probekörpern sowie Verfahren zum Messen der Eigenschaften der Werkstoffe, aus denen diese Probekörper hergestellt werden. Es führt Eigenschaften und Prüfverfahren auf, die zur Charakterisierung von PVC P-Werkstoffen geeignet und notwendig sind.
Die Eigenschaften wurden aus den allgemeinen Prüfverfahren in ISO 10350 1 ausgewählt. Weitere Prüf¬verfahren, die bei diesen Werkstoffen häufig angewendet werden oder von besonderer Bedeutung dafür sind, sind in diesem Dokument ebenso enthalten wie die in ISO 24023 (alle Teile) festgelegten kennzeichnenden Eigenschaften.
Plastiques - Matériaux à base de poly(chlorure de vinyle) plastifié (PVC-P) pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 24023-2:2020)
Le présent document spécifie les méthodes de préparation des éprouvettes et les méthodes d'essai qui doivent être utilisées pour la détermination des propriétés des matériaux pour moulage et extrusion à base de PVC-P. Il donne les exigences relatives à la manipulation du matériau d'essai et au conditionnement du matériau d'essai avant moulage et des éprouvettes avant essai.
Le présent document donne les modes opératoires et les conditions nécessaires à la préparation des éprouvettes, ainsi que les modes opératoires de mesure des propriétés des matériaux à partir desquels les éprouvettes sont obtenues. Il liste les propriétés et méthodes d'essai qui sont utiles et nécessaires pour caractériser les matériaux pour moulage et extrusion à base de PVC-P.
Les propriétés ont été sélectionnées parmi les méthodes d'essai générales de l'ISO 10350-1. D'autres méthodes d'essai largement en usage ou ayant une signification particulière pour ces matériaux pour moulage et extrusion sont aussi incluses dans le présent document; c'est le cas des propriétés de désignation spécifiées dans l'ISO 24023 (toutes les parties).
Polimerni materiali - Materiali na osnovi mehčanega polivinilklorida (PVC-P) za oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO 24023-2:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 24023-2:2020
01-september-2020
Nadomešča:
SIST EN ISO 2898-2:2009
Polimerni materiali - Materiali na osnovi mehčanega polivinilklorida (PVC-P) za
oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje
lastnosti (ISO 24023-2:2020)
Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part
2: Preparation of test specimens and determination of properties (ISO 24023-2:2020)
Kunststoffe - Weichmacherhaltige Polyvinylchlorid(PVC-P)-Werkstoffe - Teil 2:
Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 24023-2:2020)
Plastiques - Matériaux à base de poly(chlorure de vinyle) plastifié (PVC-P) pour moulage
et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO
24023-2:2020)
Ta slovenski standard je istoveten z: EN ISO 24023-2:2020
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 24023-2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 24023-2:2020
---------------------- Page: 2 ----------------------
SIST EN ISO 24023-2:2020
EN ISO 24023-2
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2020
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 2898-2:2008
English Version
Plastics - Plasticized poly(vinyl chloride) (PVC-P)
moulding and extrusion materials - Part 2: Preparation of
test specimens and determination of properties (ISO
24023-2:2020)
Plastiques - Matériaux à base de poly(chlorure de Kunststoffe - Weichmacherhaltige
vinyle) plastifié (PVC-P) pour moulage et extrusion - Polyvinylchlorid(PVC-P)-Werkstoffe - Teil 2:
Partie 2: Préparation des éprouvettes et détermination Herstellung von Probekörpern und Bestimmung von
des propriétés (ISO 24023-2:2020) Eigenschaften (ISO 24023-2:2020)
This European Standard was approved by CEN on 15 May 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 24023-2:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 24023-2:2020
EN ISO 24023-2:2020 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 24023-2:2020
EN ISO 24023-2:2020 (E)
European foreword
This document (EN ISO 24023-2:2020) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2020, and conflicting national standards
shall be withdrawn at the latest by November 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 2898-2:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 24023-2:2020 has been approved by CEN as EN ISO 24023-2:2020 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 24023-2:2020
---------------------- Page: 6 ----------------------
SIST EN ISO 24023-2:2020
INTERNATIONAL ISO
STANDARD 24023-2
First edition
2020-05
Plastics — Plasticized poly(vinyl
chloride) (PVC-P) moulding and
extrusion materials —
Part 2:
Preparation of test specimens and
determination of properties
Plastiques — Matériaux à base de poly(chlorure de vinyle) plastifié
(PVC-P) pour moulage et extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés
Reference number
ISO 24023-2:2020(E)
©
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 24023-2:2020
ISO 24023-2:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 24023-2:2020
ISO 24023-2:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Preparation of test specimens . 2
4.1 General . 2
4.2 Treatment of the material before moulding . 2
4.3 Compression moulding . 2
5 Conditioning of test specimens . 3
6 Determination of properties . 3
Annex A (normative) Detailed description of the preparation of test specimens .5
© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 24023-2:2020
ISO 24023-2:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials, in collaboration with the European Committee for Standardization (CEN)
Technical Committee CEN/TC 249, Plastics, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This first edition of ISO 24023-2 cancels and replaces ISO 2898-2:2008, which has been technically
revised.
The main changes compared to the previous edition are as follows:
— ISO 3167 has been replaced by ISO 20753;
— IEC 60093 has been replaced by the new editions of IEC 62631-3-1and IEC 62631-3-2.
A list of all parts in the ISO 24023 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 24023-2:2020
INTERNATIONAL STANDARD ISO 24023-2:2020(E)
Plastics — Plasticized poly(vinyl chloride) (PVC-P)
moulding and extrusion materials —
Part 2:
Preparation of test specimens and determination of
properties
1 Scope
This document specifies the methods of preparation of test specimens and the test methods to be used
in determining the properties of PVC-P moulding and extrusion materials. It gives the requirements for
handling test materials and for conditioning both the test material before moulding and the specimens
before testing.
This document gives procedures and conditions for the preparation of test specimens and procedures
for measuring properties of the materials from which these specimens are made. It lists properties and
test methods which are suitable and necessary to characterize PVC-P moulding and extrusion materials.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in
wide use for, or of particular significance to, these moulding and extrusion materials are also i
...
SLOVENSKI STANDARD
oSIST prEN ISO 24023-2:2019
01-maj-2019
3ROLPHUQLPDWHULDOL0DWHULDOLQDRVQRYLPHKþDQHJDSROLYLQLONORULGD 39&3 ]D
REOLNRYDQMHLQHNVWUXGLUDQMHGHO 3ULSUDYDSUHVNXãDQFHYLQXJRWDYOMDQMH
ODVWQRVWL ,62',6
Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part
2: Preparation of test specimens and determination of properties (ISO/DIS 24023-
2:2019)
Kunststoffe - Weichmacherhaltige Polyvinylchlorid(PVC-P)-Werkstoffe - Teil 2:
Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO/DIS 24023-
2:2019)
Plastiques - Matériaux à base de poly(chlorure de vinyle) plastifié (PVC-P) pour moulage
et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés
(ISO/DIS 24023-2:2019)
Ta slovenski standard je istoveten z: prEN ISO 24023-2
ICS:
83.080.20 Plastomeri Thermoplastic materials
oSIST prEN ISO 24023-2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 24023-2:2019
---------------------- Page: 2 ----------------------
oSIST prEN ISO 24023-2:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 24023-2
ISO/TC 61/SC 9 Secretariat: KATS
Voting begins on: Voting terminates on:
2019-03-15 2019-06-07
Plastics — Plasticized poly(vinyl chloride) (PVC-P)
moulding and extrusion materials —
Part 2:
Preparation of test specimens and determination of
properties
Plastiques — Matériaux à base de poly(chlorure de vinyle) plastifié (PVC-P) pour moulage et extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés
ICS: 83.080.20
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 24023-2:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019
---------------------- Page: 3 ----------------------
oSIST prEN ISO 24023-2:2019
ISO/DIS 24023-2:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 24023-2:2019
ISO/DIS 24023-2:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Preparation of test specimens . 2
4.1 General . 2
4.2 Treatment of the material before moulding . 2
4.3 Compression moulding . 2
5 Conditioning of test specimens . 3
6 Determination of properties . 3
Annex A (normative) Detailed description of the preparation of test specimens .5
© ISO 2019 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 24023-2:2019
ISO/DIS 24023-2:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www .iso .org/iso/foreword .html.
The committee responsible for this document is Technical Committee ISO/TC 61, Plastics, Subcommittee
SC 9, Thermoplastic materials.
This first edition cancels and replaces ISO 2898-2:2008, which has been technically revised.
The main changes compared to the previous edition are as follows:
— ISO 3167 is replaced by ISO 20753.
— IEC 60093 is replaced by the new edition of IEC 62631-3-1, IEC 62631-3-2.
A list of all parts in the ISO ##### series can be found on the ISO website.
iv © ISO 2019 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 24023-2:2019
DRAFT INTERNATIONAL STANDARD ISO/DIS 24023-2:2019(E)
Plastics — Plasticized poly(vinyl chloride) (PVC-P)
moulding and extrusion materials —
Part 2:
Preparation of test specimens and determination of
properties
1 Scope
This part of ISO ##### specifies the methods of preparation of test specimens and the test methods to
be used in determining the properties of PVC-P moulding and extrusion materials. Requirements for
handling test materials and for conditioning both the test material before moulding and the specimens
before testing are given.
Procedures and conditions for the preparation of test specimens and procedures for measuring
properties of the materials from which these specimens are made are given. Properties and test methods
which are suitable and necessary to characterize PVC-P moulding and extrusion materials are listed.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in
wide use for, or of particular significance to, these moulding and extrusion materials are also included
in this part of ISO #####, as are the designatory properties specified in ISO #####.
In order to obtain reproducible and comparable test results, it is necessary to use the methods of
preparation and conditioning, the specimen dimensions and the test procedures specified herein.
Values determined will not necessarily be identical to those obtained using specimens of different
dimensions or prepared using different procedures.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 176, Plastics — Determination of loss of plasticizers — Activated carbon method
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 293, Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 458-2, Plastics — Determination of stiffness in torsion of flexible materials — Part 2: Application to
plasticized compounds of homopolymers and copolymers of vinyl chloride
ISO 527-1, Plastics — Determination of tensile properties — Part 1: General principles
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 868, Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore
hardness)
ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pyknometer method and titration method
ISO 2818, Plastics — Pr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.