Multilayer piping systems for hot and cold water installations inside buildings - Part 3: Fittings (ISO 21003-3:2008)

The system Standard, of which this is Part 3, specifies the requirements for a multilayer piping system. The multilayer piping system is intended to be used for hot and cold water installations inside buildings. In respect of potential adverse effects on the quality of water intended for human consumption, caused by the product
covered by ISO 21003:
This Standard provides no information as to whether the product may be used without restriction in any of the Member States of the EU or EFTA;
It should be noted that, while awaiting the adoption of verifiable European criteria, existing national regulations concerning the use and/or the characteristics of this product stay in force. Requirements and test methods for components of the multilayer piping systems are specified in Part 1 and Part 3 of ISO 21003. Characteristics for fitness for purpose (mainly for joints) are covered in Part 5.
This part of ISO 21003 specifies the characteristics of fittings.

Mehrschichtverbund-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation innerhalb von Gebäuden - Teil 3: Formstücke (ISO 21003-3:2008)

Dieser Teil der ISO 21003 legt die Eigenschaften von Formstücken für Mehrschichtverbund-Rohrleitungs¬systeme fest, die in Warm- und Kaltwasserinstallationen innerhalb von Gebäuden für den Transport von Trink- oder Brauchwasser (Hausinstallation) sowie für Heizungsanlagen unter Berücksichtigung des betreffenden zulässigen Betriebsdruckes und der für die jeweilige Anwendungsklasse geltenden Temperaturen (siehe ISO 21003-1, Tabelle 1) eingesetzt werden. Die druckbelasteten Kunststoffe sind PE-RT, PE-X, PB, PP, PVC-C.
Diese Norm behandelt Formstücke für Schweißverbindungen, Klebverbindungen und mechanische Rohr¬verbinder, Anwendungsklassen, die sich auf Betriebsbedingungen beziehen, sowie Betriebsdruckklassen.
Diese Norm legt ebenfalls die Prüfparameter für die darin behandelten Prüfverfahren fest.
Für andere Bestandteile der Mehrschichtverbund-Rohrleitungssysteme gelten die Anforderungen und Prüfverfahren in Teil 1 und Teil 2 der ISO 21003. Eigenschaften für die Gebrauchstauglichkeit (hauptsächlich von Verbindungen) sind in Teil 5 der ISO 21003 festgelegt.
Es liegt in der Verantwortung des Käufers oder Auftraggebers, die geeignete Auswahl aus diesen Anforderungen festzulegen unter Berücksichtigung der besonderen Anforderungen und aller zutreffenden nationalen Vorschriften sowie Verlegevorschriften und Regeln.
ANMERKUNG   Für die Anwendung dieser Internationalen Norm gelten sowohl vernetztes Polyethylen (PE-X) als auch Klebstoffe als thermoplastische Werkstoffe.

Systemes de canalisations multicouches pour installations d'eau chaude et froide a l'intérieur des bâtiments - Partie 3: Raccords (ISO 21003-3:2008)

L'ISO 21003-3:2008 spécifie les caractéristiques des raccords pour les systèmes de canalisations multicouches destinés aux installations d'eau chaude et froide à l'intérieur des bâtiments pour le transport de l'eau, destinée ou non à la consommation humaine (systèmes domestiques) et aux installations de chauffage, à des pressions et des températures correspondant à la classe d'application.
Elle spécifie aussi les paramètres d'essai pour les méthodes d'essai auxquelles il est fait référence dans la présente partie de l'ISO 21003.
L'ISO 21003 est une norme de produits de référence. Elle s'applique aux tubes, aux raccords, à leurs assemblages et aux assemblages avec des composants d'autres matières plastiques et non plastiques destinés aux installations d'eau chaude et froide. L'ISO 21003-3 est censée être utilisée uniquement conjointement avec toutes les autres parties de l'ISO 21003.

Večslojni cevni sistemi za napeljave z vročo in hladno vodo v stavbah - 3. del: Fitingi (ISO 21003-3:2008)

General Information

Status
Published
Publication Date
03-Dec-2008
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
11-Nov-2008
Due Date
16-Jan-2009
Completion Date
04-Dec-2008

Relations

Buy Standard

Standard
EN ISO 21003-3:2009
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 21003-3:2009
01-januar-2009
9HþVORMQLFHYQLVLVWHPL]DQDSHOMDYH]YURþRLQKODGQRYRGRYVWDYEDKGHO
)LWLQJL ,62
Multilayer piping systems for hot and cold water installations inside buildings - Part 3:
Fittings (ISO 21003-3:2008)
Mehrschichtverbund-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation
innerhalb von Gebäuden - Teil 3: Formstücke (ISO 21003-3:2008)
Systemes de canalisations multicouches pour installations d'eau chaude et froide a
l'intérieur des bâtiments - Partie 3: Raccords (ISO 21003-3:2008)
Ta slovenski standard je istoveten z: EN ISO 21003-3:2008
ICS:
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST EN ISO 21003-3:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 21003-3:2009

---------------------- Page: 2 ----------------------

SIST EN ISO 21003-3:2009
EUROPEAN STANDARD
EN ISO 21003-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2008
ICS 23.040.45; 91.140.60

English Version
Multilayer piping systems for hot and cold water installations
inside buildings - Part 3: Fittings (ISO 21003-3:2008)
Systèmes de canalisations multicouches pour installations Mehrschichtverbund-Rohrleitungssysteme für die Warm-
d'eau chaude et froide à l'intérieur des bâtiments - Partie 3: und Kaltwasserinstallation innerhalb von Gebäuden - Teil 3:
Raccords (ISO 21003-3:2008) Formstücke (ISO 21003-3:2008)
This European Standard was approved by CEN on 15 June 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21003-3:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 21003-3:2009
EN ISO 21003-3:2008 (E)
Contents Page
Foreword.3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 21003-3:2009
EN ISO 21003-3:2008 (E)
Foreword
This document (EN ISO 21003-3:2008) has been prepared by Technical Committee ISO/TC 138 "Plastics
pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2009, and conflicting national standards shall be withdrawn at
the latest by January 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative Annex ZA, B, C or D, which is an integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 21003-3:2008 has been approved by CEN as a EN ISO 21003-3:2008 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 21003-3:2009

---------------------- Page: 6 ----------------------

SIST EN ISO 21003-3:2009

INTERNATIONAL ISO
STANDARD 21003-3
First edition
2008-07-01


Multilayer piping systems for hot and
cold water installations inside
buildings —
Part 3:
Fittings
Systèmes de canalisations multicouches pour installations d'eau
chaude et froide à l'intérieur des bâtiments —
Partie 3: Raccords





Reference number
ISO 21003-3:2008(E)
©
ISO 2008

---------------------- Page: 7 ----------------------

SIST EN ISO 21003-3:2009
ISO 21003-3:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2008 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 21003-3:2009
ISO 21003-3:2008(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 3
4 Symbols and abbreviated terms . 3
5 Material characteristics. 3
5.1 Plastics fitting materials specified in reference product standards . 3
5.2 Plastics fitting materials not specified in reference product standards. 3
5.3 Metallic fitting material. 4
5.4 Influence on water intended for human consumption. 4
6 General characteristics . 4
6.1 Appearance . 4
6.2 Opacity. 4
7 Geometrical characteristics. 4
7.1 General. 4
7.2 Dimensions of sockets for socket weld, electrofusion and solvent-cemented fittings . 4
7.3 Dimensions of metallic fittings. 5
8 Mechanical characteristics of plastics fittings (internal pressure test). 5
8.1 General. 5
8.2 Plastics fitting materials specified in reference product standards . 5
8.3 Plastics fitting materials not specified in reference product standards. 5
9 Physical and chemical characteristics of plastics fittings. 6
9.1 Plastics fitting materials specified in reference product standards . 6
9.2 Plastics fitting materials not specified in reference product standards. 6
9.3 Sealing elements. 6
10 Performance requirements . 6
11 Marking . 7
11.1 General requirements. 7
11.2 Minimum required marking. 7
Annex A (normative) List of reference product standards . 8
Bibliography . 9

© ISO 2008 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 21003-3:2009
ISO 21003-3:2008(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 21003-3 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the
transport of fluids, Subcommittee SC 2, Plastics pipes and fittings for water supplies.
ISO 21003 consists of the following parts, under the general title Multilayer piping systems for hot and cold
water installations inside buildings:
⎯ Part 1: General
⎯ Part 2: Pipes
⎯ Part 3: Fittings
⎯ Part 5: Fitness for purpose of the system
⎯ Part 7: Guidance for the assessment of conformity [Technical Specification]
NOTE ISO 21003 does not include a Part 4: Ancillary equipment, or a Part 6: Guidance for installation.
iv © ISO 2008 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 21003-3:2009
ISO 21003-3:2008(E)
Introduction
The system standard of which this is Part 3 specifies the requirements for a multilayer piping system.
The multilayer piping system is intended to be used for hot and cold water installations inside buildings.
In respect of potentially adverse effects on the quality of water intended for human consumption caused by the
products covered by ISO 21003:
⎯ no information is provided as to whether the products may be used without restriction in any of the
member states of the EU or EFTA;
⎯ it should be noted that, while awaiting the adoption of verifiable European criteria, existing national
regulations concerning the use and/or the characteristics of these products remain in force.
Requirements and test methods for materials and components other than fittings are specified in ISO 21003-1
and ISO 21003-2. Characteristics for fitness for purpose (mainly for joints) are covered in ISO 21003-5.
ISO/TS 21003-7 gives guidance on the assessment of conformity.
This part of ISO 21003 specifies the characteristics of fittings.
Other system standards which, at the date of publication of this part of ISO 21003, had been published for
plastics piping systems used for the same application are listed in Annex A.

© ISO 2008 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 21003-3:2009

---------------------- Page: 12 ----------------------

SIST EN ISO 21003-3:2009
INTERNATIONAL STANDARD ISO 21003-3:2008(E)

Multilayer piping systems for hot and cold water installations
inside buildings —
Part 3:
Fittings
1 Scope
This part of ISO 21003 specifies the characteristics of fittings for multilayer piping systems intended to be
used for hot and cold water installations inside buildings for the conveyance of water — whether or not the
water is intended for human consumption (domestic systems) or for heating systems — under specified
design pressures and temperatures appropriate to the class of application (see Table 1 of ISO 21003-1:2008).
It also specifies the test parameters for the test methods referred to in this part of ISO 21003.
ISO 21003 is a reference product standard. It is applicable to multilayer pipes, fittings, their joints, and also to
joints with components made of other plastics and non-plastics materials intended to be used for hot and cold
water installations. This part of ISO 21003 is intended for use only in conjunction with all the other parts of
ISO 21003.
This part of ISO 21003 covers fusion, solvent-cemented and mechanical fittings for a range of service
conditions (application classes) and design pressures. It is not applicable for values of design temperature, T ,
D
maximum design temperature, T , and malfunction temperature, T , in excess of those in Table 1 of
max ma
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.