Dentistry — Rotary bur instruments — Part 2: Finishing burs — Amendment 1

Art dentaire — Instruments rotatifs de fraisage — Partie 2: Fraises à polir — Amendement 1

General Information

Status
Published
Publication Date
11-Jun-2008
Current Stage
6060 - International Standard published
Due Date
22-May-2009
Completion Date
12-Jun-2008
Ref Project

Relations

Buy Standard

Standard
ISO 3823-2:2003/Amd 1:2008
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 3823-2:2003/Amd 1:2008
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 3823-2
Second edition
2003-05-15
AMENDMENT 1
2008-07-01


Dentistry — Rotary bur instruments —
Part 2:
Finishing burs
AMENDMENT 1
Art dentaire — Instruments rotatifs de fraisage —
Partie 2: Fraises à polir
AMENDEMENT 1





Reference number
ISO 3823-2:2003/Amd.1:2008(E)
©
ISO 2008

---------------------- Page: 1 ----------------------
ISO 3823-2:2003/Amd.1:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2008 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3823-2:2003/Amd.1:2008(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO 3823-2:2003 was prepared by Technical Committee ISO/TC 106, Dentistry,
Subcommittee SC 4, Dental instruments.

© ISO 2008 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 3823-2:2003/Amd.1:2008(E)

Dentistry — Rotary bur instruments —
Part 2:
Finishing burs
AMENDMENT 1
Page 9, 5.3.5.7, Table 7
Change the value for the dimension d from “0,05 mm” to “0,5 mm”.
3
In the following tables, add the following colour code in the specified lines:
Page 10, 5.3.6.1, Table 8
Table 8: add a column for colour and modify values as follows:
Designation
l
Number 2
d d l Colour
of nominal
1 2 1
of blades
± 0,5
diameter
Shank Shank Shank Shank
(Nominal size) nom. tol. max. min. min. Type 1 Type 2 Type 3 Type 3
Standard Standard Standard Short
018 1,8 ± 0,08 1,20 1,35 30 white 22,0 44,5 19,0 16,5

Page 13, 5.3.6.4.1, Table 11
...

NORME ISO
INTERNATIONALE 3823-2
Deuxième édition
2003-05-15
AMENDEMENT 1
2008-07-01



Art dentaire — Instruments rotatifs de
fraisage —
Partie 2:
Fraises à polir
AMENDEMENT 1
Dentistry — Rotary bur instruments —
Part 2: Finishing burs
AMENDMENT 1





Numéro de référence
ISO 3823-2:2003/Amd.1:2008(F)
©
ISO 2008

---------------------- Page: 1 ----------------------
ISO 3823-2:2003/Amd.1:2008(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.


DOCUMENT PROTÉGÉ PAR COPYRIGHT


©  ISO 2008
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse

ii © ISO 2008 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 3823-2:2003/Amd.1:2008(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'Amendement 1 à l'ISO 3823-2:2003 a été élaboré par le comité technique ISO/TC 106, Art dentaire,
sous-comité SC 4, Instruments dentaires.

© ISO 2008 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 3823-2:2003/Amd.1:2008(F)

Art dentaire — Instruments rotatifs de fraisage —
Partie 2:
Fraises à polir
AMENDEMENT 1
Page 9, 5.3.5.7, Tableau 7
Changer la valeur de la dimension d de «0,05 mm» en «0,5 mm».
3
Dans les tableaux ci-après, ajouter le code couleur suivant aux lignes spécifiées:
Page 10, 5.3.6.1, Tableau 8
Ajouter et modifier comme suit:
Désignation
l
Nombre 2
d d l Couleur
du diamètre
1 2 1
de dents
± 0,5
nominal
Queue Queue Que
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.