Test methods for determining the contribution to the fire resistance of structural members - Part 9: Applied fire protection systems to steel beams with web openings

This European Standard specifies a test and assessment method for determining the contribution made by fire protection systems to the fire resistance of structural steel beam I and H members in the horizontal plane containing openings in the web which may affect the structural performance of the beam. This European Standard applies to beams subject to 3 or 4 sided fire exposure.
For any beam with a single web opening or where the web openings are considered to be of small diameter in relation to the web depth the applicability of this European Standard needs to be determined by a structural engineer.
This European Standard applies to fire protection materials that have already been tested and assessed in accordance with EN 13381 4 or EN 13381-8. i.e. this European Standard cannot be used in isolation. Use of this European Standard requires the multi-temperature analysis (MTA) derived from EN 13381 4 or EN 13381 8 as the basis for determining thickness for beams with web openings. This MTA needs to be carried out on the web and bottom flange separately generating an elemental multi-temperature analysis (EMTA). The bottom flange EMTA may be used as the top flange EMTA when a beam is subject to 4 sided exposure.
This European Standard contains the fire test methodology, which specifies the tests which need to be carried out to provide data on the thermal characteristics of the fire protection system, when exposed to the standard temperature/time curve specified in EN 1363 1.
This European standard also contains the assessment, which prescribes how the analysis of the test data should be made and gives guidance on the procedures which should be undertaken.
The assessment procedure is used to establish:
a)    on the basis of the temperature data derived from testing unloaded steel sections, the thermal response of the fire protection system on cellular beams (the thermal performance);
b)   the temperature ratio between the web post and the web reference temperature, which will vary depending on the web post width;
c)   the temperature ratio between points around the web openings and the web reference area.
d)   The elemental multi temperature analysis from either EN 13381 4 or EN 13381 8 needs to be reassessed and reported against elemental A/V for each fire resistance period.
e)   A structural model needs to be used to derive limiting temperatures for cellular beams using the data from b), c) and d) above.

Prüfverfahren zur Bestimmung des Beitrages zum Feuerwiderstand von tragenden Bauteilen - Teil 9: Brandschutzmaßnahmen für Stahlträger mit Stegöffnungen

Diese Europäische Norm legt ein Prüf- und Beurteilungsverfahren zur Bestimmung des Beitrages von Brand-schutzsystemen zum Feuerwiderstand von tragenden Stahlträgern mit I- und H-Profilen in der horizontalen Ebene fest, die Öffnungen im Steg aufweisen, die die bautechnische Leistungsfähigkeit beeinflussen können. Diese Europäische Norm gilt für Träger, die an 3 oder 4 Seiten der Brandeinwirkung ausgesetzt sind.
Für Träger mit einer einzelnen Öffnung im Steg oder bei denen der Durchmesser der Stegöffnungen im Ver¬hältnis zur Stegtiefe als klein gilt, muss die Anwendbarkeit dieser Europäischen Norm durch einen Tragwerks¬planer bestimmt werden.
Diese Europäische Norm gilt für Brandschutzmaterialien, die bereits nach EN 13381 4 oder EN 13381 8 geprüft und bewertet wurden, d. h. diese Europäische Norm kann nicht losgelöst davon angewendet werden. Für die Anwendung dieser Europäische Norm ist die aus EN 13381 4 oder EN 13381-8 abgeleitete Mehrfachtemperaturanalyse (MTA) als Grundlage für die Bestimmung der Brandschutzdicke für Träger mit Stegöffnungen erforderlich. Diese MTA muss am Steg und am Unterflansch getrennt durchgeführt werden, was zu einer elementaren Mehrfachtemperaturanalyse (EMTA) führt. Die EMTA für den Unterflansch darf bei Trägern, die einer 4 seitigen Brandeinwirkung ausgesetzt sind, als EMTA für den Oberflansch verwendet werden.
Diese Europäische Norm enthält eine Methodik für Brandprüfungen, die die Prüfungen beschreibt, die zur Ermittlung von Daten über die thermischen Eigenschaften des Brandschutzsystems bei Beanspruchung unter den Bedingungen der Einheits-Temperaturzeitkurve nach EN 1363-1 durchzuführen sind.
Diese Europäische Norm enthält darüber hinaus die Beurteilung, die festlegt, wie die Analyse der Messwerte durchgeführt werden sollte, sowie Hinweise zu den anzuwendenden Verfahren.
Das Verfahren der Beurteilung wird angewendet, um:
a)   auf der Grundlage der Temperaturmesswerte, die sich aus den Prüfungen von unbelasteten Stahlprofilen ergeben, das thermische Verhalten des Brandschutzsystems auf Lochstegträgern zu ermitteln (ther¬mische Leistungsfähigkeit);
b)   das Verhältnis der Temperatur des Stegpfostens zur Bezugstemperatur des Stegs, das in Abhängigkeit von der Breite des Stegpfostens schwankt, zu ermitteln;
c)   das Verhältnis der Temperatur der Punkte um die Stegöffnungen herum zur Temperatur im Bezugs¬bereich des Stegs zu ermitteln.
d)   Die elementare Mehrfachtemperaturanalyse entweder aus EN 13381 4 oder EN 13381 8 muss erneut bewertet und im Vergleich zum elementaren A/V-Verhältnis für jede Feuerwiderstandsdauer angegeben werden.
e)   Es ist ein Strukturmodell zu verwenden, um die Grenztemperaturen für Lochstegträger anhand der vorstehenden Angaben aus b), c) und d) abzuleiten.

Méthodes d'essai pour déterminer la contribution à la résistance au feu des éléments de construction - Partie 9: Systèmes de protection au feu appliqués aux poutres alvéolaires en acier

La présente Norme européenne spécifie une méthode d'essai et d'évaluation permettant de déterminer la contribution des systèmes de protection au feu à la résistance au feu des éléments en I et en H des poutres en acier de construction dans le plan horizontal contenant des ouvertures dans l'âme susceptibles d'affecter la performance structurelle de la poutre. La présente Norme européenne s'applique aux poutres soumises à une exposition au feu sur 3 ou 4 côtés.
Pour les poutres ayant une seule ouverture d'âme ou dont les ouvertures d'âme ont un petit diamètre par rapport à la hauteur de l'âme, l'applicabilité de la présente Norme européenne doit être déterminée par un ingénieur en construction.
La présente Norme européenne s'applique aux matériaux de protection au feu qui ont déjà été soumis à l'essai et évalués conformément à l'EN 13381 4 ou à l'EN 13381-8, ce qui signifie que la présente norme ne peut pas être utilisée isolément. L'utilisation de la présente Norme européenne nécessite d'employer l'analyse de plusieurs températures (MTA) tirée de l'EN 13381 4 ou de l'EN 13381 8 comme base de la détermination de l'épaisseur à appliquer aux poutres alvéolaires. Cette MTA doit être conduite séparément sur l'âme et sur la semelle inférieure en générant une analyse élémentaire de plusieurs températures (EMTA). L'EMTA de la semelle inférieure peut être utilisée comme l'EMTA de la semelle supérieure lorsqu'une poutre est soumise à une exposition sur les 4 côtés.
La présente Norme européenne contient la méthodologie d’essai au feu, qui spécifie les essais devant être réalisés pour fournir des données sur les caractéristiques thermiques du système de protection au feu lorsqu’il est exposé à la courbe normalisée température/temps spécifiée dans l’EN 1363 1.
La présente Norme européenne comprend également l'évaluation qui prescrit la façon d'effectuer l'analyse des données d'essai et spécifie les lignes directrices des modes opératoires qu'il convient d'entreprendre.
Le mode opératoire de l'évaluation permet d'établir :
a)   d'après les températures tirées des essais effectués sur des petits tronçons d'acier non chargés, la réponse thermique du système de protection au feu sur les poutres alvéolaires (les performances thermiques) ;
b)   le rapport de températures entre la température de la membrure pleine et la température de référence de l'âme, qui variera en fonction de la largeur de la membrure pleine ;
c)   le rapport de températures entre les points situés autour des ouvertures d'âme et la surface de référence de l'âme.
d)   L'analyse élémentaire de plusieurs températures issue de l'EN 13381 4 ou de l'EN 13381 8 doit être réévaluée et rapportée en fonction du facteur de massiveté élémentaire A/V pour chaque durée de résistance au feu.
e)   Un modèle structurel doit être utilisé pour déduire les températures limites des poutres alvéolaires à l'aide des données tirées de b), c) et d) ci-dessus.

Preskusne metode za ugotavljanje prispevka k požarni odpornosti konstrukcijskih elementov - 9. del: Požarno zaščitni sistemi za jeklene nosilce z odprtinami v stojini

Ta evropski standard določa metodo za preskušanje in oceno za ugotavljanje prispevka požarno zaščitnega sistema k požarni odpornosti konstrukcijskih jeklenih nosilcev I in H z odprtinami v stojini v vodoravnem položaju. Ta standard se uporablja za nosilce, ki so izpostavljeni ognju iz 3 ali 4 strani.
Ta standard se uporablja za protipožarne materiale, ki so že bili preskušeni in ocenjeni v skladu s standardoma EN 13381-4 ali EN13381-8. tj. standard prEN 13381-9 ne sme biti uporabljen samostojno. Uporaba standarda prEN 13381-9 zahteva multitemperaturno analizo (MTA) iz standarda EN 13381-4 ali EN 13381-8 kot osnovo za določanje debeline nosilcev z odprtinami v stojini. Analizo MTA je treba izvesti v stojini in spodnji prirobnici ter v obeh primerih ustvariti elementarno multitemperaturno analizo (EMTA). EMTA spodnje prirobnice se lahko uporabi kot EMTA zgornje prirobnice, če je nosilec izpostavljen ognju iz štirih strani.
Ta evropski standard vključuje metodologijo preskušanja požarne varnosti, ki določa preskuse, ki jih je treba opraviti za pridobitev podatkov o toplotnih lastnostih sistema protipožarnega varstva v času izpostavljenosti standardni krivulji temperatura-čas, določeni v standardu EN 1363-1.
Ta evropski standard prav tako vsebuje presojo, ki predpisuje način analiziranja podatkov preskusa, in navodila o postopkih, ki jih je treba izvesti.
Postopek ocenjevanja se uporablja za ugotavljanje:
a) toplotnega odziva požarno zaščitnega sistema na celične nosilce (toplotno delovanje) na podlagi podatkov o temperaturi, pridobljenih pri preskušanju delovanja neobremenjenih profilov;
b) toplotnega razmerja med temperaturo stojine in referenčno temperaturo stojine, ki niha glede na širino stojine;
c) temperaturnega razmerja med točkami okoli odprtin v stojini in referenčnim področjem stojine;
d) elementarne multitemperaturne analize iz standarda EN 13381-4 ali EN 13381-8, ki jo je treba znova oceniti in o njej poročati v povezavi z elementarnim A/V za vsako obdobje požarne odpornosti.
Strukturni model je treba uporabiti za določanje mejnih temperatur za celične nosilce z uporabo podatkov iz b), c) in d) zgoraj.

General Information

Status
Published
Publication Date
23-Jun-2015
Withdrawal Date
30-Dec-2015
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
11-May-2021

Buy Standard

Standard
EN 13381-9:2015
English language
40 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.RQVWUXNFLMVNLKVWRMLQLPrüfverfahren zur Bestimmung des Beitrages zum Feuerwiderstand von tragenden Bauteilen - Teil 9: Brandschutzmaßnahmen für Stahlträger mit StegöffnungenMéthodes d'essai pour déterminer la contribution à la résistance au feu des éléments de construction - Partie 9: Systèmes de protection au feu appliqués aux poutres alvéolaires en acierTest methods for determining the contribution to the fire resistance of structural members - Part 9: Applied fire protection systems to steel beams with web openings13.220.50Požarna odpornost gradbenih materialov in elementovFire-resistance of building materials and elementsICS:Ta slovenski standard je istoveten z:EN 13381-9:2015SIST EN 13381-9:2015en,fr,de01-september-2015SIST EN 13381-9:2015SLOVENSKI
STANDARD



SIST EN 13381-9:2015



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13381-9
June 2015 ICS 13.220.50; 91.080.10 English Version
Test methods for determining the contribution to the fire resistance of structural members - Part 9: Applied fire protection systems to steel beams with web openings
Méthodes d'essai pour déterminer la contribution à la résistance au feu des éléments de construction - Partie 9: Systèmes de protection au feu appliqués aux poutres alvéolaires en acier
Prüfverfahren zur Bestimmung des Beitrages zum Feuerwiderstand von tragenden Bauteilen - Teil 9: Brandschutzmaßnahmen für Stahlträger mit StegöffnungenThis European Standard was approved by CEN on 20 May 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13381-9:2015 ESIST EN 13381-9:2015



EN 13381-9:2015 (E) 2 Contents Page Foreword .4 Introduction .5 1 Scope .6 2 Normative references .7 3 Terms and definitions, symbols and units .7 3.1 Terms and definitions .7 3.2 Symbols and units .9 4 Test equipment .9 4.1 General .9 4.2 Furnace .9 4.3 Test conditions .9 5 Test specimens . 10 5.1 General .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.