iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1998-2:2005/AC:2010

(Corrigendum)

Eurocode 8 - Design of structures for earthquake resistance - Part 2: Bridges

Eurocode 8 - Design of structures for earthquake resistance - Part 2: Bridges

TC - Editorial modifications to "National annex for EN 1998-2", 4.2.4.4, 5.6.2 and 6.2.2 in the three language versions of the mother standard.
2013: Originator of XML version: first setup pilot of CCMC in 2012

Eurocode 8 - Auslegung von Bauwerken gegen Erdbeben - Teil 2: Brücken

Eurocode 8 - Calcul des structures pour leur résistance aux séismes - Partie 2: Ponts

Evrokod 8 - Projektiranje konstrukcij na potresnih območjih - 2. del: Mostovi

EN 1991-2 opredeljuje zunanje obtežbe (modele in značilne vrednosti), povezane s cestnim prometom, vplive pešcev in železniškega prometa, ki po potrebi vključujejo dinamične učinke in centrifugalne, zaviralne in pospeševalne vplive ter vplive nezgod. Zunanji vplivi, opredeljeni v EN 1991-2, so namenjeni uporabi za načrtovanje novih mostov, vključno s podmostniki, oporniki, pokončnimi zidovi, poševnimi krilnimi zidovi in bočnimi zidovi itd., in njihovih temeljev. Modele obtežbe in vrednosti, podane v EN 1991-2, je treba uporabljati pri načrtovanju opornih zidov ob cestah in železniških progah. EN 1991-2 je namenjen uporabi v povezavi z EN 1990 (zlasti A2) in od EN 1991 do EN 1999. Razdelek 1 podaja definicije in simbole. Razdelek 2 opredeljuje načela obremenitev za cestne mostove, mostove za pešce ali kolesarje in železniške mostove. Razdelek 3 obravnava projektne situacije ter podaja navodila glede istočasnosti modelov prometne obtežbe in glede kombinacij z neprometnimi vplivi. Razdelek 4 opredeljuje: - zunanje obtežbe (modele in značilne vrednosti) zaradi prometnih vplivov na cestne mostove in njihove pogoje vzajemne kombinacije, in kombinacije s prometom pešcev in  kolesarjev (glej razdelek 5) ; - druge vplive, posebej za načrtovanje cestnih mostov. Razdelek 5 opredeljuje: - zunanje obtežbe (modele in značilne vrednosti) na poteh za pešce, kolesarje; in na mostovih za pešce; - druge vplive, posebej za načrtovanje mostov za pešce. Razdelka 4 in 5 tudi opredeljujeta obtežbe, ki se prenašajo na konstrukcijo s sistemov za zadrževanje vozil in/ali ograj za pešce. Razdelek 6 opredeljuje: - zunanje vplive zaradi železniškega prometa na mostove; - druge vplive, posebej za načrtovanje železniških mostov in sosednjih konstrukcij.

General Information

Status
Published
Publication Date
09-Feb-2010
ICS
91.120.25 - Seismic and vibration protection
93.040 - Bridge construction
Technical Committee
CEN/TC 250 - Structural Eurocodes
Drafting Committee
CEN/TC 250/SC 8 - Eurocode 8: Earthquake resistance design of structures
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
10-Feb-2010
Completion Date
10-Feb-2010
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Mandate
M/265 - Mandate to CEN for the conversion of the Eurocodes from ENV into EN concerning the structural and geotechnical design of buildings and civil engineering works
M/BC/CEN/89/11 - Framework mandate to CEN on Eurocode work : execution of a standardization programme on Eurocodes for the structural design of building and civil engineering works
Ref Project
SIST EN 1998-2:2006/AC:2010 - Eurocode 8 - Design of structures for earthquake resistance - Part 2: Bridges

Relations

Corrects
EN 1998-2:2005 - Eurocode 8 - Design of structures for earthquake resistance - Part 2: Bridges
Effective Date
12-Dec-2009

Buy Standard

EN 1998-2:2006/AC:2010EN 1998-2:2006/AC:2010
PreviousNext
Corrigendum
EN 1998-2:2006/AC:2010
English language
2 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Eurocode 8 - Auslegung von Bauwerken gegen Erdbeben - Teil 2: BrückenEurocode 8 - Calcul des structures pour leur résistance aux séismes - Partie 2: PontsEurocode 8 - Design of structures for earthquake resistance - Part 2: Bridges93.040Gradnja mostovBridge construction91.120.25YLEUDFLMDPLSeismic and vibration protectionICS:Ta slovenski standard je istoveten z:EN 1998-2:2005/AC:2010SIST EN 1998-2:2006/AC:2010en,fr,de01-maj-2010SIST EN 1998-2:2006/AC:2010SLOVENSKI
STANDARD



SIST EN 1998-2:2006/AC:2010



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1998-2:2005/AC
February 2010
Février 2010
Februar 2010 ICS 91.120.25; 93.040 English version Version Française Deutsche Fassung
Eurocode 8 - Design of structures for earthquake resistance - Part 2: Bridges
Eurocode 8 - Calcul des structures pour leur résistance aux séismes - Partie 2: Ponts
Eurocode 8 - Auslegung von Bauwerken gegen Erdbeben - Teil 2: Brücken This corrigendum becomes effective on 10 February 2010 for incorporation in the three official language versions of the EN.
Ce corrigendum prendra effet le 10 février 2010 pour incorporation dans les trois versions linguistiques officielles de la EN.
Die Berichtigung tritt am 10.Februar 2010 zur Einarbeitung in die drei offiziellen Sprachfassungen der EN in Kraft.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Tous droits d'exploitation sous quelque forme et de quelque manière que ce soit réservés dans le mond
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 1998-2:2005/A2:2011(Amendment)
Eurocode 8: Design of structures for earthquake resistance - Part 2: Bridges
SIST EN 1998-2:2006/A2:2012

(1)   The scope of Eurocode 8 is defined in EN 1998-1:2004, 1.1.1 and the scope of this Standard is defined in 1.1.1. Additional parts of Eurocode 8 are indicated in EN 1998-1:2004, 1.1.3.
(2)   Within the framework of the scope set forth in EN 1998-1:2004, this part of the Standard contains the particular Performance Requirements, Compliance Criteria and Application Rules applicable to the design of earthquake resistant bridges.
(3)   This Part primarily covers the seismic design of bridges in which the horizontal seismic actions are mainly resisted through bending of the piers or at the abutments; i.e. of bridges composed of vertical or nearly vertical pier systems supporting the traffic deck superstructure. It is also applicable to the seismic design of cable-stayed and arched bridges, although its provisions should not be considered as fully covering these cases.
(4)   Suspension bridges, timber and masonry bridges, moveable bridges and floating bridges are not included in the scope of this Part.
(5)   This Part contains only those provisions that, in addition to other relevant Eurocodes or relevant Parts of EN 1998, should be observed for the design of bridges in seismic regions. In cases of low seismicity, simplified design criteria may be established (see 2.3.7(1)).
(6)   The following topics are dealt with in the text of this Part:
Basic requirements and Compliance Criteria,
Seismic Action,
Analysis,
Strength Verification,
Detailing.
This Part also includes a special section on seismic isolation with provisions covering the application of this method of seismic protection to bridges.
(7)   Annex G contains rules for the calculation of capacity design effects.
(8)   Annex J contains rules regarding the variation of design properties of seismic isolator units and how such variation may be taken into account in design.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1998-2:2005/A1:2009(Amendment)
Eurocode 8: Design of structures for earthquake resistance - Part 2: Bridges
SIST EN 1998-2:2006/A1:2009

EUROCODE - NO CONSOLIDATION AT PUBLICATION
2013: Originator of XML version: first setup pilot of CCMC in 2012

  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1998-2:2005(Main)
Eurocode 8 - Design of structures for earthquake resistance - Part 2: Bridges
SIST EN 1998-2:2006

Complementary to EN 1992-2, EN 1993-2 and EN 1994-2. Design rules for earthquake resistant design of steel, concrete and composite bridges.

  • Standard
    146 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 1998-2(Main)
Eurocode 8 - Design of structures for earthquake resistance - Part 2: Bridges
oSIST prEN 1998-2:2023

EN 1998-2 is intended to be applied to the design of new bridges in seismic regions. It covers the design of reinforced concrete, steel and composite steel-concrete bridges and provides guidance for the design of timber bridges.
EN 1998-2 is applicable to the seismic design of bridges exploiting ductility in structural members or through the use of antiseismic devices. When ductility is exploited, this part primarily covers bridges in which the horizontal seismic actions are mainly resisted through bending of the piers or at the abutments; i.e. of bridges composed of vertical or nearly vertical pier systems supporting the traffic deck superstructure. It is also applicable to the seismic design of arched bridges, although its provisions should not be considered as fully covering these cases.
Suspension bridges and masonry bridges, moveable bridges and floating bridges are not included in the scope of EN 1998-2.

  • Draft
    87 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1998-2:2005/A2:2011(Amendment)
Eurocode 8: Design of structures for earthquake resistance - Part 2: Bridges
SIST EN 1998-2:2006/A2:2012

(1)   The scope of Eurocode 8 is defined in EN 1998-1:2004, 1.1.1 and the scope of this Standard is defined in 1.1.1. Additional parts of Eurocode 8 are indicated in EN 1998-1:2004, 1.1.3.
(2)   Within the framework of the scope set forth in EN 1998-1:2004, this part of the Standard contains the particular Performance Requirements, Compliance Criteria and Application Rules applicable to the design of earthquake resistant bridges.
(3)   This Part primarily covers the seismic design of bridges in which the horizontal seismic actions are mainly resisted through bending of the piers or at the abutments; i.e. of bridges composed of vertical or nearly vertical pier systems supporting the traffic deck superstructure. It is also applicable to the seismic design of cable-stayed and arched bridges, although its provisions should not be considered as fully covering these cases.
(4)   Suspension bridges, timber and masonry bridges, moveable bridges and floating bridges are not included in the scope of this Part.
(5)   This Part contains only those provisions that, in addition to other relevant Eurocodes or relevant Parts of EN 1998, should be observed for the design of bridges in seismic regions. In cases of low seismicity, simplified design criteria may be established (see 2.3.7(1)).
(6)   The following topics are dealt with in the text of this Part:
Basic requirements and Compliance Criteria,
Seismic Action,
Analysis,
Strength Verification,
Detailing.
This Part also includes a special section on seismic isolation with provisions covering the application of this method of seismic protection to bridges.
(7)   Annex G contains rules for the calculation of capacity design effects.
(8)   Annex J contains rules regarding the variation of design properties of seismic isolator units and how such variation may be taken into account in design.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1998-2:2005/A1:2009(Amendment)
Eurocode 8: Design of structures for earthquake resistance - Part 2: Bridges
SIST EN 1998-2:2006/A1:2009

EUROCODE - NO CONSOLIDATION AT PUBLICATION
2013: Originator of XML version: first setup pilot of CCMC in 2012

  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1998-2:2005(Main)
Eurocode 8 - Design of structures for earthquake resistance - Part 2: Bridges
SIST EN 1998-2:2006

Complementary to EN 1992-2, EN 1993-2 and EN 1994-2. Design rules for earthquake resistant design of steel, concrete and composite bridges.

  • Standard
    146 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 1998-2(Main)
Eurocode 8 - Design of structures for earthquake resistance - Part 2: Bridges
oSIST prEN 1998-2:2023

EN 1998-2 is intended to be applied to the design of new bridges in seismic regions. It covers the design of reinforced concrete, steel and composite steel-concrete bridges and provides guidance for the design of timber bridges.
EN 1998-2 is applicable to the seismic design of bridges exploiting ductility in structural members or through the use of antiseismic devices. When ductility is exploited, this part primarily covers bridges in which the horizontal seismic actions are mainly resisted through bending of the piers or at the abutments; i.e. of bridges composed of vertical or nearly vertical pier systems supporting the traffic deck superstructure. It is also applicable to the seismic design of arched bridges, although its provisions should not be considered as fully covering these cases.
Suspension bridges and masonry bridges, moveable bridges and floating bridges are not included in the scope of EN 1998-2.

  • Draft
    87 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22435:2024(Main)
Gas cylinders - Cylinder valves with integrated pressure regulators - Specification and type testing (ISO 22435:2024)
kSIST FprEN ISO 22435:2024

This document specifies design, type test methods, marking and instruction requirements for cylinder valves with integrated pressure regulators (VIPRs) intended to be fitted to gas cylinders, pressure drums or tubes or used as a main valve for bundles of cylinders that convey compressed, liquefied or dissolved gases.
These are requirements for VIPRs that are in addition to those given in the relevant closure standard, for example, in ISO 10297 for cylinder valves, in ISO 17871 for quick-release cylinder valves, in ISO 17879 for self-closing cylinder valves or in ISO 23826 for ball valves. For ISO 17871, these requirements are only applicable to quick-release cylinder valves types B, C, D and E.
NOTE 1        If the pressure regulating system of a VIPR is acting as the primary valve operating mechanism, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826. This also includes designs where closure of the primary valve operating mechanism of a VIPR is obtained by closing the seat of the pressure regulating system.
NOTE 2        If the primary valve operating mechanism of a VIPR is located at the low-pressure side of the pressure regulating system, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826.
NOTE 3        The term “pressure receptacle” is used within this document to cover instances where no differentiation is necessary between gas cylinders, bundles of cylinders, pressure drums and tubes.
This document does not apply to VIPRs for
a)       medical applications (see ISO 10524-3);
b)       liquefied petroleum gas (LPG);
c)        cryogenic applications.
NOTE 4        Additional requirements for a VIPR with a residual pressure device (RPD) are specified in ISO 15996.
NOTE 5        Additional requirements for pressure relief valves can exist in international/regional regulations/ standards.

  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17015-1:2024(Main)
Electronic Public Procurement - Catalogue - Part 1: Choreographies
kSIST FprEN 17015-1:2024

The purpose of this deliverable is to specify and describe choreographies for exchanging an electronic product catalogue (“catalogues”) as part of the business processes in the pre-award and post-award area, so that catalogues can serve as a basis for placing orders as well as evaluating tenders. The key aspects covered by this choreography specification are:
-   processes for submitting catalogues from the selling to the buying side;
-   processes for submitting catalogue-related data as part of a tendering process;
-   processes integrating sell-side procurement systems.
This document does not apply to the transactions used in the specified choreographies. These transactions are specified in EN 17015 2. The relationship between the choreographies and the transaction is described in Clause 8.
The identifier of this choreographies document is EN 17015 1:2024.
How to claim compliance to this choreography is specified in 6.2.3.

  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day