iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 17150:2019

(Main)

Plastics piping systems for non-pressure underground conveyance and storage of non-potable water - Test method for determination of short-term compression strength of boxes

Plastics piping systems for non-pressure underground conveyance and storage of non-potable water - Test method for determination of short-term compression strength of boxes

This document specifies a method for determining short-term compression strength on boxes made of thermoplastics materials for non-pressure underground conveyance and storage of non-potable water.

Kunststoff-Rohrleitungssysteme für die drucklose unterirdische Entwässerung für Nicht-Trinkwasser - Prüfverfahren zur Bestimmung der Kurzzeitdruckfestigkeit von Versickerungsblöcken

Dieses Dokument legt ein Verfahren zur Bestimmung der Kurzzeitdruckfestigkeit an Versickerungsblöcken aus thermoplastischen Werkstoffen für die drucklose unterirdische Entwässerung und Speicherung von Nicht-Trinkwasser fest.

Systèmes de canalisations en plastique pour le transport et le stockage souterrains sans pression de l’eau non potable - Méthode d’essai pour la détermination de la résistance à la compression à court terme des structures alvéolaires ultra-légères

Le présent document spécifie une méthode pour déterminer la résistance à la compression à court terme des structures alvéolaires ultra-légères (SAUL) fabriquées à partir de matières thermoplastiques pour le transport et le stockage souterrains sans pression de l’eau non potable.

Cevni sistemi iz polimernih materialov, ki delujejo po težnostnem principu in so položeni v zemljo, za transport in shranjevanje vode, ki ni namenjena pitju - Preskusna metoda za ugotavljanje kratkotrajne tlačne odpornosti zabojev

Ta evropski standard določa metodo za ugotavljanje kratkotrajne tlačne odpornosti zabojev iz termoplastičnih materialov, ki delujejo po težnostnem principu in so položeni v zemljo, za transport in shranjevanje vode, ki ni namenjena pitju.

General Information

Status
Published
Publication Date
20-Aug-2019
Withdrawal Date
27-Feb-2021
ICS
23.040.01 - Pipeline components and pipelines in general
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 26 - Storm Water Management
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
21-Aug-2019
Due Date
15-Dec-2018
Completion Date
21-Aug-2019
Ref Project
SIST EN 17150:2019 - Plastics piping systems for non-pressure underground conveyance and storage of non-potable water - Test method for determination of short-term compression strength of boxes

Buy Standard

EN 17150:2019EN 17150:2019
PreviousNext
Standard
EN 17150:2019
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 17150:2019
01-oktober-2019
Cevni sistemi iz polimernih materialov, ki delujejo po težnostnem principu in so
položeni v zemljo, za transport in shranjevanje vode, ki ni namenjena pitju -
Preskusna metoda za ugotavljanje kratkotrajne tlačne odpornosti zabojev
Plastics piping systems for non-pressure underground conveyance and storage of non-
potable water - Test method for determination of short-term compression strength of
boxes
Kunststoff-Rohrleitungssysteme für die drucklose unterirdische Entwässerung für Nicht-
Trinkwasser - Prüfverfahren zur Bestimmung der Kurzzeitdruckfestigkeit von
Versickerungsblöcken
Systèmes de canalisations en plastique pour le transport et le stockage souterrains sans
pression de l’eau non potable - Méthode d’essai pour la détermination de la résistance à
la compression à court terme des structures alvéolaires ultra-légères
Ta slovenski standard je istoveten z: EN 17150:2019
ICS:
23.040.03 Cevovodi za zunanje sisteme Pipeline and its parts for
transporta vode in njihovi deli external water conveyance
systems
SIST EN 17150:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 17150:2019

---------------------- Page: 2 ----------------------
SIST EN 17150:2019


EN 17150
EUROPEAN STANDARD

NORME EUROPÉENNE

August 2019
EUROPÄISCHE NORM
ICS 23.040.01
English Version

Plastics piping systems for non-pressure underground
conveyance and storage of non-potable water - Test
method for determination of short-term compression
strength of boxes
Systèmes de canalisations en plastique pour le Kunststoff-Rohrleitungssysteme für die drucklose
transport et le stockage souterrains sans pression de unterirdische Entwässerung für Nicht-Trinkwasser -
l'eau non potable - Méthode d'essai pour la Prüfverfahren zur Bestimmung der
détermination de la résistance à la compression à court Kurzzeitdruckfestigkeit von Versickerungsblöcken
terme des structures alvéolaires ultra-légères
This European Standard was approved by CEN on 19 October 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17150:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 17150:2019
EN 17150:2019 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Symbols and units . 5
5 Principle . 5
5.1 General . 5
5.2 Method A: Constant load rate .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
CEN/TS 1566-2:2023(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Assessment of conformity
SIST-TS CEN/TS 1566-2:2023

This document gives guidance for specifying requirements for the AoC of compounds/formulations, products, joints and assemblies in accordance with the applicable part of EN 1566 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   A basic test matrix provides an overview of the testing scheme in Annex A.
In conjunction with EN 1566 1 (see European foreword), this document is applicable to solid-wall piping systems made of chlorinated poly(vinyl chloride) (PVC C) intended to be used for or soil and waste discharge systems (low and high temperature):
-   inside buildings (application area code "B");
-   for both inside buildings and buried in ground within the building structure (application area code "BD").

  • Technical specification
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 1455-2:2023(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 2: Assessment of conformity
SIST-TS CEN/TS 1455-2:2023

This document gives guidance for specifying requirements for the AoC of compounds/formulation, products, joints and assemblies in accordance with the applicable part of EN 1455 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   A basic test matrix provides an overview of the testing scheme in Annex A.
In conjunction with EN 1455-1 (see European foreword), this document is applicable to solid wall piping systems made of acrylonitrile-butadiene-styrene (ABS) intended to be used for soil and waste discharge (low and high temperature):
-   inside buildings (application area code "B");
-   both inside buildings and buried in ground within the building structure (application area code "BD").

  • Technical specification
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1401-1:2019+A1:2023(Main)
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1401-1:2019+A1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of unplasticized poly(vinyl chloride) (PVC U) piping systems in the field of non-pressure underground drainage and sewerage:
- buried in ground outside the building structure (application area code "U"), and
- both buried in ground, within the building structure and outside the building (application area code "UD").
NOTE 1   The intended use is reflected in the marking of products by "U" or "UD".
It also specifies the test parameters for the test methods referred to in this document.
NOTE 2   Multilayer pipes with different formulations throughout the wall and foamed core pipes are covered by EN 13476-2 [1].
This document covers a range of nominal sizes, a range of pipes and fittings series and a range of stiffness classes and gives recommendations concerning colours.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It is applicable to PVC U pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
NOTE 4   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 16.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1455-1:2022(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1455-1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) piping systems intended for soil and waste discharge applications (low and high temperature):
- inside buildings (application area code “B”);
- for both inside buildings and buried in ground within the building structure (application area code “BD”).
NOTE 1 The intended use is reflected in the marking of products by “B” or “BD”.
NOTE 2 Application “B” covers uses above ground inside buildings, or outside buildings fixed onto the wall.
NOTE 3 Pipes and fittings of the pipe series S 25 are intended to be used for application area “B” only.
NOTE 4 For use buried in ground within the building structure are intended only those components (marked with “BD”) with nominal outside diameters equal to or greater than 75 mm.
NOTE 5 EN 476 [5] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this document fully meet these requirements.
This document is also applicable to ABS and ASA pipes, fittings and the system intended for the following purposes:
- ventilating part of the pipework in association with discharge applications;
- rainwater pipework within the building structure.
It also specifies the test parameters for the test methods that are referred to.
This document covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.
NOTE 6 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 7 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex A can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 21.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1566-1:2022(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1566-1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of chlorinated poly(vinyl chloride) (PVC-C) piping systems intended for soil and waste discharge (low and high temperature):
- inside buildings (application area code “B”);
- for both inside buildings and buried in ground within the building structure (application area code “BD”).
NOTE 1 The intended use is reflected in the marking of products by “B” or “BD”.
NOTE 2 Application “B” covers uses above ground inside buildings, or outside buildings fixed onto the wall.
NOTE 3 Pipes and fittings of the pipe series S 25 are intended to be used for application area “B” only.
NOTE 4 For use buried in ground within the building structure are intended only those components (marked with “BD”) with nominal outside diameters equal to or greater than 75 mm.
NOTE 5 EN 476 [5] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this document fully meet these requirements.
This document is applicable to PVC-C pipes and fittings and the system intended for the following purposes:
- ventilating part of the pipework in association with discharge applications;
- rainwater pipework within the building structure.
It also specifies the test parameters for the test methods that are referred to.
This document covers a range of nominal sizes, a range of pipe series and gives recommendations concerning colours.
NOTE 6 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 7 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex A can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 21.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 17152-3:2022(Main)
Plastics piping systems for non-pressure underground conveyance and storage of non-potable water - Boxes used for infiltration, attenuation and storage systems - Part 3: Conformity assessment scheme
SIST-TS CEN/TS 17152-3:2023

This document gives guidance for requirements for the assessment of conformity (AoC) of materials, compounds, formulations, products, and assemblies in accordance with the applicable part(s) of EN 17152 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   Annex B, Table B.1 contains a summary of tests for TT and surveillance monitoring.
In conjunction with EN 17152 1 (see European foreword) this document is applicable to boxes used for infiltration, attenuation and storage systems.

  • Technical specification
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15874-1:2013/A1:2022(Amendment)
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General - Amendment 1: Impact test (ISO 15874-1:2013/Amd 1:2022)
SIST EN ISO 15874-1:2013/A1:2022
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11295:2022(Main)
Plastics piping systems used for the rehabilitation of pipelines - Classification and overview of strategic, tactical and operational activities (ISO 11295:2022)
SIST EN ISO 11295:2022

This document specifies the steps of the overall process of pipeline rehabilitation, comprising:
—    information on strategic and tactical activities:
a) investigation and condition assessment of the existing pipeline;
b) pipeline rehabilitation planning.
—    information on and requirements for operational activities:
c) project specification;
d) applications of techniques;
e) documentation of the design and application process.
Definitions and classification of families of renovation and trenchless replacement techniques are provided, and their respective features described. Areas of application covered include underground drainage and sewerage networks and underground water and gas supply networks.
The following aspects are not covered by the scope of this document:
—    new construction provided as network extensions;
—    calculation methods to determine, for each viable technique, the characteristics of lining or replacement pipe material needed to secure the desired performance of the rehabilitated pipeline;
—    techniques providing non-structural pressure pipe liners;
—    techniques for local repair.
It is the responsibility of the designer to choose and design the renovation or trenchless replacement pipeline system.

  • Standard
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 1555-7:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
SIST-TS CEN/TS 1555-7:2022

This document gives guidance for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of EN 1555 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
This document gives recommendations that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001.
NOTE 1 If certification is involved, the certification and inspection body is preferably compliant with EN ISO/IEC 17065, EN IS0/IEC 17021 or EN ISO/IEC 17020, as applicable.
In conjunction with Parts 1 to 5 of EN 1555 (see Foreword), this document is applicable to polyethylene (PE) plastics piping systems for the supply of gaseous fuels. It is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions:
a) a maximum operating pressure, MOP, up to and including 10 bar;
b) an operating temperature of 20 °C as reference temperature.
NOTE 2 For other operating temperatures, derating coefficients can be used; see EN 1555-5.

  • Technical specification
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15877-3:2009/A2:2021(Amendment)
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings - Amendment 2 (ISO 15877-3:2009/Amd 2:2021)
SIST EN ISO 15877-3:2009/A2:2021
  • Amendment
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day